3Com WL-560 manual Industry Canada IC Emissions Compliance Statement

Page 67

CANADA – INDUSTRY CANADA (IC)

This device complies with RSS 210 of Industry Canada.

Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of this device.”

L ‘ utilisation de ce dispositif est autorisée seulement aux conditions suivantes: (1) il ne doit pas produire de brouillage et (2) l’ utilisateur du dispositif doit étre prêt à accepter tout brouillage radioélectrique reçu, même si ce brouillage est susceptible de compromettre le fonctionnement du dispositif.

The term "IC" before the equipment certification number only signifies that the Industry Canada technical specifications were met.

To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (EIRP) is not more than that required for successful communication. To prevent radio interference to the licensed service, this device is intended to be operated indoors and away from windows to provide maximum shielding. Equipment (or its transmit antenna) that is installed outdoors is subject to licensing.

Pour empecher que cet appareil cause du brouillage au service faisant l'objet d'une licence, il doit etre utilize a l'interieur et devrait etre place loin des fenetres afin de Fournier un ecram de blindage maximal. Si le matriel (ou son antenne d'emission) est installe a l'exterieur, il doit faire l'objet d'une licence.

High power radars are allocated as primary users of the 5.25 to 5.35 GHz and 5.65 to 5.85 GHz bands. These radar stations can cause interference with and/or damage this device.

INDUSTRY CANADA (IC) EMISSIONS COMPLIANCE STATEMENT

This Class B digital apparatus complies with Canadian ICES-003.

AVIS DE CONFORMITÉ À LA RÉGLEMENTATION D’INDUSTRIE CANADA

Cet appareil numérique de la classe B est conform à la norme NMB-003 du Canada.

SAFETY COMPLIANCE NOTICE

This device has been tested and certified according to the following safety standards and is intended for use only in Information Technology Equipment which has been tested to these or other equivalent standards:

■UL Standard 60950 (3rd Edition) or 60950-1

■CAN/CSA C22.2 No. 60950 or 60950-1

■IEC 60950 or 60950-1

■EN 60950 or 60950-1

Image 67

Contents 3Com 11a/b/g Wireless Workgroup Bridge User Guide 3Com Corporation Campus Drive Marlborough MA USA Contents Configuring the Bridge END User License Agreement Regulatory Information Page About this Guide Following ConventionsRelated DocumentationDocumentation documentation Product Registration Support Introduction 802.11g 802.11aPlanning ConfigurationNetwork Configuration and Planning NetworkWorkgroup Ad-Hoc Network ConfigurationsWireless Infrastructure Network ExampleBridge UnpackingBridge Wall-Mounting the Bridge Deciding Where to Place the BridgeRouting Cable Under the Cradle Securing the Locking Bar Connecting the Power ConnectingConnecting the Bridge About the Client List Connecting to a HubNetwork printers in areas that are not wired for Ethernet LED IndicatorsDetermining if you Need to ConfigureAttaching An External AntennaNetworks without a Dhcp Server Determining if you Need to Configure the BridgeTo Wireless Client Infrastructure Bridge Default SettingsUsing the 3Com Installation CD Using the 3Com Installation CDInstalling the Bridge Configuring the Bridge Device Manager Using the 3ComWireless InfrastructureUsing the 3Com Wireless Infrastructure Device Manager Click ConfigureButton Description Management UsingSystem Moving to a new configuration Clearing Applying System Configuration SettingsSystem Properties Apply Server, select Obtain an IP address automatically and clickSelect 802.11a to set the Bridge to operate with either Select Wireless Client Infrastructure to associate with anSelect Specify the Wireless LAN Service Area to allow Service AreaBeing used, click Long Wi-Fi Interoperable External and one internal antenna this settingSet the Data Preamble 40/64-bit Shared Key WEP No Security Open System128/152-bit Shared Key 104/128-bit Shared KeyAES Or DisableSecondary Radius Using the Configuration Management System About Uart Configuring Operation ModeConfiguring Network Serial Port Settings Configuring Uart SettingsReset Applying SettingsOr with the Bridge out of the cradle Under Tools, click Restore Factory DefaultsUsing Tftp Using FTP defaultUnder Tools, click Backup Wireless Workgroup Bridge Using HttpUnder Tools, click Restore Wireless Workgroup Bridge Summary Page Diagnosing ProblemsTroubleshooting Disconnecting the Bridge DisconnectingUninstalling Uninstall 3Com Wireless Infrastructure Device ManagerFirmware Upgrading BridgeProduct to Gain Service BenefitsSolve Problems Register YourPurchase Extended WarrantyProfessional Services Access SoftwareContact Us Directory of 3Com resources by region atLatin America Telephone Technical Support and Repair END User License Agreement Page Regulatory Information MANUFACTURER’S Declaration of Conformity Industry Canada IC Emissions Compliance Statement Europe EU Declaration of Conformity Bipt Indoor/Outdoor