3Com WL-560 manual Indoor/Outdoor

Page 70

EUROPE – RESTRICTIONS FOR USE OF 5GHZ FREQUENCIES IN EUROPEAN COMMUNITY COUNTRIES

	European Community	5150-5250 MHz	5250-5350 MHz	5470-5725MHz
	Countries	Channels: 36, 40,	Channels: 52, 56,	Channels: 100, 104,
		Channels: 36, 40,	Channels: 52, 56,	Channels: 100, 104,
		44, 48	60, 64	108, 112, 116, 120,
				124, 128, 132, 136, 140
		Indoor Only	Indoor Only	Indoor/Outdoor

	Austria
		✔	X	X

	Belgium, France,
	Switzerland,	✔	✔	X
	Liechtenstein	✔	✔	X
	Liechtenstein

	Denmark, Finland,
	Germany, Greece,
	Iceland, Ireland, Italy,
	Luxembourg,	✔	✔	✔
	Netherlands, Norway,
	Portugal, Spain, Sweden,
	UK

✔allowed X not allowed

■To remain in conformance with European spectrum usage laws for Wireless LAN operation, the above 2.4GHz and 5GHz channel limitations apply. The user should check the current channel of operation. If operation is occurring outside of the allowable frequencies as listed above, the user must cease operating the 11a/b/g Wireless Workgroup Bridge at that location and consult the local technical support staff responsible for the wireless network.

■The 5GHz Turbo mode feature is not allowed for operation in any European Community country.

■This device must not be operated in ad-hoc mode using channels in the 5GHz bands in the European Community. Ad-hoc mode provides a direct communication between two client devices without a Wireless LAN Access Point.

■This device must be used with Access Points that have employed and activated a radar detection feature required for European Community operation in the 5GHz bands. This device will operate under the control of the Access Point in order to avoid operating on a channel occupied by any radar system in the area. The presence of nearby radar operation may result in temporary interruption in communications of this device. The Access Point’s radar detection feature will automatically restart operation on a channel free of radar. You may consult with the local technical support staff responsible for the wireless network to ensure the Access Point device(s) are properly configured for European Community operation.

Image 70

Contents 3Com 11a/b/g Wireless Workgroup Bridge User Guide 3Com Corporation Campus Drive Marlborough MA USA Contents Configuring the Bridge END User License Agreement Regulatory Information Page About this Guide Documentation ConventionsRelated FollowingDocumentation documentation Product Registration Support Introduction 802.11a 802.11gNetwork ConfigurationNetwork Configuration and Planning PlanningExample ConfigurationsWireless Infrastructure Network Workgroup Ad-Hoc NetworkUnpacking BridgeBridge Deciding Where to Place the Bridge Wall-Mounting the BridgeRouting Cable Under the Cradle Securing the Locking Bar Connecting Connecting the PowerAbout the Client List Connecting to a Hub Connecting the BridgeNetwork printers in areas that are not wired for Ethernet Indicators LEDExternal Antenna Need to ConfigureAttaching An Determining if youDetermining if you Need to Configure the Bridge Networks without a Dhcp ServerBridge Default Settings To Wireless Client InfrastructureUsing the 3Com Installation CD Using the 3Com Installation CDInstalling the Bridge Configuring the Bridge Infrastructure Using the 3ComWireless Device ManagerClick Configure Using the 3Com Wireless Infrastructure Device ManagerButton Description Management UsingSystem Clearing Applying System Configuration Settings Moving to a new configurationSystem Properties Server, select Obtain an IP address automatically and click ApplySelect Wireless Client Infrastructure to associate with an Select 802.11a to set the Bridge to operate with eitherService Area Select Specify the Wireless LAN Service Area to allowExternal and one internal antenna this setting Being used, click Long Wi-Fi InteroperableSet the Data Preamble No Security Open System 40/64-bit Shared Key WEP104/128-bit Shared Key 128/152-bit Shared KeyOr Disable AESSecondary Radius Using the Configuration Management System Configuring Operation Mode About UartConfiguring Uart Settings Configuring Network Serial Port SettingsApplying Settings ResetUnder Tools, click Restore Factory Defaults Or with the Bridge out of the cradleUsing FTP default Using TftpUsing Http Under Tools, click Backup Wireless Workgroup BridgeUnder Tools, click Restore Wireless Workgroup Bridge Summary Page Problems DiagnosingTroubleshooting Uninstall 3Com Wireless Infrastructure Device Manager DisconnectingUninstalling Disconnecting the BridgeUpgrading Bridge FirmwareRegister Your Service BenefitsSolve Problems Product to GainAccess Software WarrantyProfessional Services Purchase ExtendedDirectory of 3Com resources by region at Contact UsLatin America Telephone Technical Support and Repair END User License Agreement Page Regulatory Information MANUFACTURER’S Declaration of Conformity Industry Canada IC Emissions Compliance Statement Europe EU Declaration of Conformity Bipt Indoor/Outdoor