3Com WL-560 manual END User License Agreement

Page 63

END USER LICENSE AGREEMENT

Customer shall take all steps necessary to protect Wind River's and its licensors' proprietary rights in the Run-Time Module and to ensure that each Run-Time Module distributed by Customer will be accompanied by a localized copy of an End User License Agreement.

Such End User License Agreement shall prohibit the End User from: (i) copying the Run-Time Module, except for archive purposes consistent with the End User's archive procedures; (ii) transferring the Run-Time Module to a third party apart from the Target Application; (iii) modifying, decompiling, disassembling, reverse engineering or otherwise attempting to derive the Source Code of the Run-Time Module; (iv) exporting the Run-Time Module or underlying technology in contravention of applicable U.S. and foreign export laws and regulations; and (v) using the Run-Time Module other than in connection with operation of the Target Application.

In addition, the End User License Agreement shall: (i) state that the Run-Time Module is licensed, not sold and that Customer and its licensors retain ownership of all copies of the Run-Time Module; (ii) expressly disclaim all implied warranties, including without limitation the implied warranties of merchantability, fitness for a particular purpose, title and non-infringement; (iii) exclude liability for any special, indirect, punitive, incidental and consequential damages; and (iv) require that any further distribution of the Run-Time Module be subject to the same restrictions set forth herein.

The End User License Agreement shall also state that, with respect to the Run-Time Module, Wind River and its licensors are third party beneficiaries of the End User License Agreement and that the provisions related to the Run-Time Module are made expressly for the benefit of, and are enforceable by, Wind River and its licensors.

Image 63

Contents 3Com 11a/b/g Wireless Workgroup Bridge User Guide 3Com Corporation Campus Drive Marlborough MA USA Contents Configuring the Bridge END User License Agreement Regulatory Information Page About this Guide Following ConventionsRelated DocumentationDocumentation documentation Product Registration Support Introduction 802.11g 802.11aPlanning ConfigurationNetwork Configuration and Planning NetworkWorkgroup Ad-Hoc Network ConfigurationsWireless Infrastructure Network ExampleBridge UnpackingBridge Wall-Mounting the Bridge Deciding Where to Place the BridgeRouting Cable Under the Cradle Securing the Locking Bar Connecting the Power ConnectingConnecting the Bridge About the Client List Connecting to a HubNetwork printers in areas that are not wired for Ethernet LED IndicatorsDetermining if you Need to ConfigureAttaching An External AntennaNetworks without a Dhcp Server Determining if you Need to Configure the BridgeTo Wireless Client Infrastructure Bridge Default SettingsUsing the 3Com Installation CD Using the 3Com Installation CDInstalling the Bridge Configuring the Bridge Device Manager Using the 3ComWireless InfrastructureUsing the 3Com Wireless Infrastructure Device Manager Click ConfigureButton Description Using ManagementSystem Moving to a new configuration Clearing Applying System Configuration SettingsSystem Properties Apply Server, select Obtain an IP address automatically and clickSelect 802.11a to set the Bridge to operate with either Select Wireless Client Infrastructure to associate with anSelect Specify the Wireless LAN Service Area to allow Service AreaBeing used, click Long Wi-Fi Interoperable External and one internal antenna this settingSet the Data Preamble 40/64-bit Shared Key WEP No Security Open System128/152-bit Shared Key 104/128-bit Shared KeyAES Or DisableSecondary Radius Using the Configuration Management System About Uart Configuring Operation ModeConfiguring Network Serial Port Settings Configuring Uart SettingsReset Applying SettingsOr with the Bridge out of the cradle Under Tools, click Restore Factory DefaultsUsing Tftp Using FTP defaultUnder Tools, click Backup Wireless Workgroup Bridge Using HttpUnder Tools, click Restore Wireless Workgroup Bridge Summary Page Diagnosing ProblemsTroubleshooting Disconnecting the Bridge DisconnectingUninstalling Uninstall 3Com Wireless Infrastructure Device ManagerFirmware Upgrading BridgeProduct to Gain Service BenefitsSolve Problems Register YourPurchase Extended WarrantyProfessional Services Access SoftwareContact Us Directory of 3Com resources by region atLatin America Telephone Technical Support and Repair END User License Agreement Page Regulatory Information MANUFACTURER’S Declaration of Conformity Industry Canada IC Emissions Compliance Statement Europe EU Declaration of Conformity Bipt Indoor/Outdoor