Radio Shack 20-426 manual FCC wants you to know, Basics

Page 10

The Basics

the FCC wants you to know

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and receiver.

Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

Consult your local RadioShack store or an experienced radio/TV technician for help.

Note

Mobile use of this scanner is unlawful or requires a

 

permit in some areas. Check the laws in your area before

 

using.

10

Image 10
Contents Pro-2051 1,000-Channel Triple Trunking Mobile/Base Scanner Contents Basics Power your scannerSet up your scanner BasicsScanning a private bank Advanced scanner featuresBeyond the Basics Highway patrol alertsWired programming Contents SkywarnSignal Stalker WarrantyYour scanner’s keypad HOLD/RESUMETo Do This Your scanner’s rear view Your scanner’s display TrunkFCC wants you to know Install your scanner Mounting the scanner in your vehicleFrom a wall outlet Power your scannerThrough your vehicle’s ignition negative ground only From your vehicle’s cigarrette lighter Rear ViewConnecting an external antenna Connecting the supplied antennaConnect your scanner Connecting an external speaker Use extreme caution when installing or removing anListening Safely Turn on your scanner Set up your scannerSet the squelch Common scanner terms Basics Listen to preprogrammed frequenciesScanning overview Basics Channel storage banks Advanced scanner featuresBeyond the Basics Storing known frequencies into channelsBeyond the Basics Beyond the Basics Deleting a stored frequency Locking out a channel in hold modeLocking out a channel in scanning mode Locking out channelsMemory lock Restoring a locked-out channel in hold modeRestoring all locked-out channels Direct channel access Beyond the Basics Hold/resumeScanning a private bank Beyond the Basics Priority scan Changing the priority channelService scanning Setting a search band Beyond the Basics Band searchData skip Search holdBeyond the Basics Frequency skip Storing search frequenciesDelay Highway patrol/local police scanning Highway patrol alertsSelecting the state State Code Order Press these buttons Action Beyond the Basics Scan hold Setting the alert tone volumeHighway warning alert Muting the alert tone Adjusting alertHighway patrol priority channels Skip frequenciesTrunked highway frequencies Skywarn About SkywarnNWR Same Programming a Fips code Programming FipsBeyond the Basics Signal Stalker Setting the signal stalker options Beyond the Basics Using signal stalker Setting the squelch Trunk trackingProgramming trunking frequencies Selecting Trunking System Type Programming id scan lists manually Motorola talk groups Edacs talk groupsLTR talk groups Receiving trunked systemsID scan mode ID scan hold modeID search mode Direct entry id hold modeID search hold mode Programming scan lists during search ID monitor modeDeleting a stored ID Reviewing ID lockout ID lockoutRestoring locked-out IDs Setting priority in trunking mode Setting the delay mode for trunking modeTrunking frequency confirmation Moving between scan list memories Multi-trackAbout multi-track Edacs tracking Programming Edacs system frequenciesBeyond the Basics An Edacs trunked system Special Edacs featuresAFS partial entry Edacs ID range search Edacs ID blockoutTracking LTR systems Edacs ScatBeyond the Basics Tracking Motorola systems fleet map programming Preset Fleet Maps E1P1 E1P5 E1P11 Selecting a Preset Fleet Map User-defined fleet mapsFleet Map Size Codes Programming a user fleet map Size code restrictionsProgramming a Hybrid system You can only enter within a range of 5-100 kHz, and 5 or Toggling the status bit Control channel only mode Disconnect tone detect option end code If the scanner receives no data from the PC for more than Cloning your scanner Replacing the fuse in the DC power cord BirdiesBeyond the Basics Resetting your scanner ProperlyFrequently asked questions FAQs Drive by patrol cars but do not hear alarms?Error appears on the display. What does it mean? Specifications If FrequenciesGlossary Service and repair Care