Radio Shack 20-426 manual Setting the delay mode for trunking mode, Trunking frequency conﬁrmation

Page 56

Beyond the Basics

bank once, while in locked out review mode, hold down L/O for 3 seconds. All locked out IDs in a bank are restored.

setting the delay mode for trunking mode

A default delay of 2 seconds is automatically set for each talk group for ID scan mode and ID search mode. To set the delay feature on or off, press DELAY while trunking. DLY will appear or disappear, depending on your setting.

trunking frequency conﬁrmation

You can check the frequency while a talk group ID is active.

Press the d key, and the active frequency on which the talk group is transmitting will ﬂash on the display. Or press and hold the d key for 2 seconds. The ID and the frequency alternately appear on the display. To cancel this mode, press the d key again.

Note

This feature is applied to ID scan mode and ID search mode.

setting priority in trunking mode

You can set priority in your scan lists, just as you do in your conventional ones. The default setting for the priority ID is the ﬁrst location in each scan list. You can set the priority by pressing and holding PRI for 2 seconds in ID scan hold mode. After you’ve set up your scan list, press PRI to activate it. It is very similar to conventional priority although there is no “interrupt” during the transmissions. Priorities are checked in between transmissions.

With priority on, you can hold on an ID in your scan list, such as scan list 3, memory location 7, and the scanner will check all the priorities in all the active scan lists in between any transmissions on the ID on which you’re holding. The lowest numbered priority will be checked ﬁrst. For example, the

56

Image 56

Contents Pro-2051 1,000-Channel Triple Trunking Mobile/Base Scanner Contents Power your scanner Set up your scannerBasics BasicsAdvanced scanner features Beyond the BasicsScanning a private bank Highway patrol alertsContents Skywarn Signal StalkerWired programming WarrantyYour scanner’s keypad HOLD/RESUMETo Do This Your scanner’s rear view Your scanner’s display TrunkFCC wants you to know Install your scanner Mounting the scanner in your vehicleThrough your vehicle’s ignition negative ground only Power your scannerFrom a wall outlet From your vehicle’s cigarrette lighter Rear ViewConnect your scanner Connecting the supplied antennaConnecting an external antenna Connecting an external speaker Use extreme caution when installing or removing anListening Safely Set the squelch Set up your scannerTurn on your scanner Scanning overview Basics Listen to preprogrammed frequenciesCommon scanner terms Basics Advanced scanner features Beyond the BasicsChannel storage banks Storing known frequencies into channelsBeyond the Basics Locking out a channel in hold mode Locking out a channel in scanning modeBeyond the Basics Deleting a stored frequency Locking out channelsRestoring all locked-out channels Restoring a locked-out channel in hold modeMemory lock Direct channel access Beyond the Basics Hold/resumeScanning a private bank Beyond the Basics Priority scan Changing the priority channelService scanning Setting a search band Beyond the Basics Band searchData skip Search holdBeyond the Basics Frequency skip Storing search frequenciesDelay Selecting the state Highway patrol alertsHighway patrol/local police scanning State Code Order Press these buttons Action Highway warning alert Setting the alert tone volumeBeyond the Basics Scan hold Adjusting alert Highway patrol priority channelsMuting the alert tone Skip frequenciesTrunked highway frequencies Skywarn About SkywarnNWR Same Programming a Fips code Programming FipsBeyond the Basics Signal Stalker Setting the signal stalker options Beyond the Basics Using signal stalker Setting the squelch Trunk trackingProgramming trunking frequencies Selecting Trunking System Type Programming id scan lists manually Motorola talk groups Edacs talk groupsLTR talk groups Receiving trunked systemsID scan mode ID scan hold mode ID search hold mode Direct entry id hold mode ID search mode Deleting a stored ID ID monitor modeProgramming scan lists during search Restoring locked-out IDs ID lockoutReviewing ID lockout Trunking frequency conﬁrmation Setting the delay mode for trunking modeSetting priority in trunking mode Moving between scan list memories Multi-trackAbout multi-track Edacs tracking Programming Edacs system frequenciesAFS partial entry Special Edacs featuresBeyond the Basics An Edacs trunked system Edacs ID range search Edacs ID blockoutTracking LTR systems Edacs ScatBeyond the Basics Tracking Motorola systems ﬂeet map programming Preset Fleet Maps E1P1 E1P5 E1P11 Selecting a Preset Fleet Map User-deﬁned ﬂeet mapsFleet Map Size Codes Programming a Hybrid system Size code restrictionsProgramming a user ﬂeet map You can only enter within a range of 5-100 kHz, and 5 or Toggling the status bit Control channel only mode Disconnect tone detect option end code If the scanner receives no data from the PC for more than Cloning your scanner Replacing the fuse in the DC power cord BirdiesBeyond the Basics Resetting your scanner ProperlyFrequently asked questions FAQs Drive by patrol cars but do not hear alarms?Error appears on the display. What does it mean? Speciﬁcations If FrequenciesGlossary Service and repair Care