Radio Shack 20-426 manual Scanning a private bank

Page 25

Beyond the Basics

scanning a private bank

You can program frequencies into channels of the private bank. There are 1000 channels in the bank. 150 of the most frequently used frequencies are preprogrammed into Channels 1 to 150. You can scan these frequencies as soon as you turn on the scanner.

1After programming frequencies, press HOLD/RESUME to begin scanning. Or repeatedly press PVT until PRIVATE appears, if the scanner is in another mode. Your scanner scans all the channels upward.

2. The bank number indicators (1-10) selected for scanning appear on the display, and the bank being currently monitored ﬂashes. You can deselect banks from active scanning by entering their numbers on your keypad. The indicator for each deselected bank disappears, and the bank’s channels are not scanned.

Note

One bank must always be active. You cannot deactivate all ten banks at the same time. If you try to deselect all the banks, the ﬁrst bank is automatically selected.

To restore a bank to active scanning, enter the bank’s number on your keypad. The bank’s indicator will display again.

During normal scanning the scanner skips unprogrammed or locked out channels. When a transmission is received, the scanner stops on that channel. When the transmission ends, scanning resumes automatically.

Notes

You can set the scanner to hold on a frequency for

two seconds allowing time for a response. For more information on the delay feature, see “Delay”.

During Signal Stalker operation, the delay time is 10 seconds. After 10 seconds have elapsed, or if you press e or HOLD/RESUME, the scanner resumes search.

25

Image 25

Contents Pro-2051 1,000-Channel Triple Trunking Mobile/Base Scanner Contents Set up your scanner Power your scannerBasics BasicsBeyond the Basics Advanced scanner featuresScanning a private bank Highway patrol alertsSignal Stalker Contents SkywarnWired programming WarrantyHOLD/RESUME Your scanner’s keypadTo Do This Your scanner’s rear view Trunk Your scanner’s displayFCC wants you to know Mounting the scanner in your vehicle Install your scannerFrom a wall outlet Power your scannerThrough your vehicle’s ignition negative ground only Rear View From your vehicle’s cigarrette lighterConnecting an external antenna Connecting the supplied antennaConnect your scanner Use extreme caution when installing or removing an Connecting an external speakerListening Safely Turn on your scanner Set up your scannerSet the squelch Common scanner terms Basics Listen to preprogrammed frequenciesScanning overview Basics Beyond the Basics Advanced scanner featuresChannel storage banks Storing known frequencies into channelsBeyond the Basics Locking out a channel in scanning mode Locking out a channel in hold modeBeyond the Basics Deleting a stored frequency Locking out channelsMemory lock Restoring a locked-out channel in hold modeRestoring all locked-out channels Beyond the Basics Hold/resume Direct channel accessScanning a private bank Changing the priority channel Beyond the Basics Priority scanService scanning Beyond the Basics Band search Setting a search bandSearch hold Data skipStoring search frequencies Beyond the Basics Frequency skipDelay Highway patrol/local police scanning Highway patrol alertsSelecting the state State Code Order Press these buttons Action Beyond the Basics Scan hold Setting the alert tone volumeHighway warning alert Highway patrol priority channels Adjusting alertMuting the alert tone Skip frequenciesTrunked highway frequencies About Skywarn SkywarnNWR Same Programming Fips Programming a Fips codeBeyond the Basics Signal Stalker Setting the signal stalker options Beyond the Basics Using signal stalker Trunk tracking Setting the squelchProgramming trunking frequencies Selecting Trunking System Type Programming id scan lists manually Edacs talk groups Motorola talk groupsReceiving trunked systems LTR talk groupsID scan hold mode ID scan modeID search mode Direct entry id hold modeID search hold mode Programming scan lists during search ID monitor modeDeleting a stored ID Reviewing ID lockout ID lockoutRestoring locked-out IDs Setting priority in trunking mode Setting the delay mode for trunking modeTrunking frequency conﬁrmation Multi-track Moving between scan list memoriesAbout multi-track Programming Edacs system frequencies Edacs trackingBeyond the Basics An Edacs trunked system Special Edacs featuresAFS partial entry Edacs ID blockout Edacs ID range searchEdacs Scat Tracking LTR systemsBeyond the Basics Tracking Motorola systems ﬂeet map programming Preset Fleet Maps E1P1 E1P5 E1P11 User-deﬁned ﬂeet maps Selecting a Preset Fleet MapFleet Map Size Codes Programming a user ﬂeet map Size code restrictionsProgramming a Hybrid system You can only enter within a range of 5-100 kHz, and 5 or Toggling the status bit Control channel only mode Disconnect tone detect option end code If the scanner receives no data from the PC for more than Cloning your scanner Birdies Replacing the fuse in the DC power cordProperly Beyond the Basics Resetting your scannerDrive by patrol cars but do not hear alarms? Frequently asked questions FAQsError appears on the display. What does it mean? If Frequencies SpeciﬁcationsGlossary Care Service and repair