Radio Shack 20-426 manual Programming a Fips code, Programming Fips

Page 40

Beyond the Basics

Although the alert beep (warning beep, watch beep, advisory beep) sounds at short intervals for 5 minutes. After that, the emergency beep will sound at intervals of 10 seconds.

programming a FIPS code

To specify a county, SAME uses a standard established by the US Census bureau, called FIPS.

The format of a FIPS code is:

PSSCCC, where...

P = area subdivision (0=entire area)

SS = State code (00=all states)

CCC = County code (000=all counties)

For example, the FIPS code for Tarrant County, Texas is:

048439 (48=Texas; 439=Tarrant County).

Some counties are further subdivided, in which cases, the ﬁrst digit will be 0 for all subdivisions in the county and each subdivision will be labeled 1-9.

To program your scanner to alert you when the weather service issues an alert, you must set the scanner to the alert mode, and then leave the scanner monitoring the weather service. You cannot scan frequencies and monitor for weather alerts at the same time.

To limit weather alerts to a speciﬁc area, you must also program in the FIPS code(s) for the area(s) you want to receive alerts. The scanner can be set to either, alert for all areas, or only the areas you have programmed.

programming FIPS

During weather scan, hold mode, press FUNC + PGM. The scanner sends itself into FIPS programming mode. If the scanner is set to alert for all FIPS, ALLFIPS appears on the display. If the scanner is set to alert only the area you have

40

Image 40

Contents Pro-2051 1,000-Channel Triple Trunking Mobile/Base Scanner Contents Power your scanner Set up your scannerBasics BasicsAdvanced scanner features Beyond the BasicsScanning a private bank Highway patrol alertsContents Skywarn Signal StalkerWired programming WarrantyYour scanner’s keypad HOLD/RESUMETo Do This Your scanner’s rear view Your scanner’s display TrunkFCC wants you to know Install your scanner Mounting the scanner in your vehicleFrom a wall outlet Power your scannerThrough your vehicle’s ignition negative ground only From your vehicle’s cigarrette lighter Rear ViewConnecting an external antenna Connecting the supplied antennaConnect your scanner Connecting an external speaker Use extreme caution when installing or removing anListening Safely Turn on your scanner Set up your scannerSet the squelch Common scanner terms Basics Listen to preprogrammed frequenciesScanning overview Basics Advanced scanner features Beyond the BasicsChannel storage banks Storing known frequencies into channelsBeyond the Basics Locking out a channel in hold mode Locking out a channel in scanning modeBeyond the Basics Deleting a stored frequency Locking out channelsMemory lock Restoring a locked-out channel in hold modeRestoring all locked-out channels Direct channel access Beyond the Basics Hold/resumeScanning a private bank Beyond the Basics Priority scan Changing the priority channelService scanning Setting a search band Beyond the Basics Band searchData skip Search holdBeyond the Basics Frequency skip Storing search frequenciesDelay Highway patrol/local police scanning Highway patrol alertsSelecting the state State Code Order Press these buttons Action Beyond the Basics Scan hold Setting the alert tone volumeHighway warning alert Adjusting alert Highway patrol priority channelsMuting the alert tone Skip frequenciesTrunked highway frequencies Skywarn About SkywarnNWR Same Programming a Fips code Programming FipsBeyond the Basics Signal Stalker Setting the signal stalker options Beyond the Basics Using signal stalker Setting the squelch Trunk trackingProgramming trunking frequencies Selecting Trunking System Type Programming id scan lists manually Motorola talk groups Edacs talk groupsLTR talk groups Receiving trunked systemsID scan mode ID scan hold modeID search mode Direct entry id hold modeID search hold mode Programming scan lists during search ID monitor modeDeleting a stored ID Reviewing ID lockout ID lockoutRestoring locked-out IDs Setting priority in trunking mode Setting the delay mode for trunking modeTrunking frequency conﬁrmation Moving between scan list memories Multi-trackAbout multi-track Edacs tracking Programming Edacs system frequenciesBeyond the Basics An Edacs trunked system Special Edacs featuresAFS partial entry Edacs ID range search Edacs ID blockoutTracking LTR systems Edacs ScatBeyond the Basics Tracking Motorola systems ﬂeet map programming Preset Fleet Maps E1P1 E1P5 E1P11 Selecting a Preset Fleet Map User-deﬁned ﬂeet mapsFleet Map Size Codes Programming a user ﬂeet map Size code restrictionsProgramming a Hybrid system You can only enter within a range of 5-100 kHz, and 5 or Toggling the status bit Control channel only mode Disconnect tone detect option end code If the scanner receives no data from the PC for more than Cloning your scanner Replacing the fuse in the DC power cord BirdiesBeyond the Basics Resetting your scanner ProperlyFrequently asked questions FAQs Drive by patrol cars but do not hear alarms?Error appears on the display. What does it mean? Speciﬁcations If FrequenciesGlossary Service and repair Care