Radio Shack 20-426 manual Programming trunking frequencies

Page 47

Beyond the Basics

too high, it could prevent your scanner from locking on the control channel reliably. If it is set too low, it will slightly delay finding the control channel. The best setting is the same

as for conventional reception and is critical for monitoring trunked systems.

programming trunking frequencies

There are three steps for programming a trunked system:

1.Program the Trunk Type - enter the type of trunking system the scanner will track -- Motorola Type II, Type I, EDACS, LTR, etc.

2.Program the trunked frequencies - within a trunked system, the frequencies are shared among all users. These frequency groups are called talk groups.

3.Program the Talk Groups - Within a trunked system, each agency or department is assigned a talk group ID. This ID must be programmed into the scanner in order for it to monitor that specific agency or department.

Before you start programming your scanner to track a trunked system, consider the following:

• You can only program one type of trunking system in each bank of your scanner.

• Trunked frequencies must be entered while in the trunk programming mode.

• If you’re in the trunk programming mode, you cannot select channels in other banks. For example, if you are programming Bank 4, you can only select channels 301- 400 by pressing e or d.

Note

If you are programming an EDACS trunked system, you

must enter the frequencies in a specific order. Check www.trunkscanner.com for details.

47

Image 47
Contents Pro-2051 1,000-Channel Triple Trunking Mobile/Base Scanner Contents Basics Power your scannerSet up your scanner BasicsHighway patrol alerts Advanced scanner featuresBeyond the Basics Scanning a private bankWarranty Contents SkywarnSignal Stalker Wired programmingHOLD/RESUME Your scanner’s keypadTo Do This Your scanner’s rear view Trunk Your scanner’s displayFCC wants you to know Mounting the scanner in your vehicle Install your scannerThrough your vehicle’s ignition negative ground only Power your scannerFrom a wall outlet Rear View From your vehicle’s cigarrette lighterConnect your scanner Connecting the supplied antennaConnecting an external antenna Use extreme caution when installing or removing an Connecting an external speakerListening Safely Set the squelch Set up your scannerTurn on your scanner Scanning overview Basics Listen to preprogrammed frequenciesCommon scanner terms Basics Storing known frequencies into channels Advanced scanner featuresBeyond the Basics Channel storage banksBeyond the Basics Locking out channels Locking out a channel in hold modeLocking out a channel in scanning mode Beyond the Basics Deleting a stored frequencyRestoring all locked-out channels Restoring a locked-out channel in hold modeMemory lock Beyond the Basics Hold/resume Direct channel accessScanning a private bank Changing the priority channel Beyond the Basics Priority scanService scanning Beyond the Basics Band search Setting a search bandSearch hold Data skipStoring search frequencies Beyond the Basics Frequency skipDelay Selecting the state Highway patrol alertsHighway patrol/local police scanning State Code Order Press these buttons Action Highway warning alert Setting the alert tone volumeBeyond the Basics Scan hold Skip frequencies Adjusting alertHighway patrol priority channels Muting the alert toneTrunked highway frequencies About Skywarn SkywarnNWR Same Programming Fips Programming a Fips codeBeyond the Basics Signal Stalker Setting the signal stalker options Beyond the Basics Using signal stalker Trunk tracking Setting the squelchProgramming trunking frequencies Selecting Trunking System Type Programming id scan lists manually Edacs talk groups Motorola talk groupsReceiving trunked systems LTR talk groupsID scan hold mode ID scan modeID search hold mode Direct entry id hold modeID search mode Deleting a stored ID ID monitor modeProgramming scan lists during search Restoring locked-out IDs ID lockoutReviewing ID lockout Trunking frequency confirmation Setting the delay mode for trunking modeSetting priority in trunking mode Multi-track Moving between scan list memoriesAbout multi-track Programming Edacs system frequencies Edacs trackingAFS partial entry Special Edacs featuresBeyond the Basics An Edacs trunked system Edacs ID blockout Edacs ID range searchEdacs Scat Tracking LTR systemsBeyond the Basics Tracking Motorola systems fleet map programming Preset Fleet Maps E1P1 E1P5 E1P11 User-defined fleet maps Selecting a Preset Fleet MapFleet Map Size Codes Programming a Hybrid system Size code restrictionsProgramming a user fleet map You can only enter within a range of 5-100 kHz, and 5 or Toggling the status bit Control channel only mode Disconnect tone detect option end code If the scanner receives no data from the PC for more than Cloning your scanner Birdies Replacing the fuse in the DC power cordProperly Beyond the Basics Resetting your scannerDrive by patrol cars but do not hear alarms? Frequently asked questions FAQsError appears on the display. What does it mean? If Frequencies SpecificationsGlossary Care Service and repair