Radio Shack 20-426 manual Beyond the Basics

Page 44

Beyond the Basics

•Hi On or Hi OFF

•UHF On or UHF OFF

•800 On or 800 OFF

4.Repeatedly press e or d until the option you want appears, then press E to select it. Otherwise, press ./CLR if you do not want to select it. Then skip to Step 9.

5.Press E while S-S.ALt appears. One of the following alert options appears:

•ALT bEEP: The scanner beeps when a signal stalker signal is detected.

•ALT OFF: The scanner does not provide any alert when a signal stalker signal is detected.

6.Repeatedly press e or d until the option you want appears, then press E to select it. Otherwise, press ./CLR if you do not want to select it. Then skip to Step 9.

7.Press E while S-S.PS appears. One of the following options appears:

•PS On: The scanner ignores common pager frequencies.

•PS OFF: The scanner does not screen common pager frequencies.

8.Repeatedly press e or d until the option you want appears, then press E to select it. Otherwise, press ./CLR if you do not want to select it.

9.When you select the option, press ./CLR to exit the option mode.

44

Image 44

Contents Pro-2051 1,000-Channel Triple Trunking Mobile/Base Scanner Contents Power your scanner Set up your scannerBasics BasicsAdvanced scanner features Beyond the BasicsScanning a private bank Highway patrol alertsContents Skywarn Signal StalkerWired programming WarrantyYour scanner’s keypad HOLD/RESUMETo Do This Your scanner’s rear view Your scanner’s display TrunkFCC wants you to know Install your scanner Mounting the scanner in your vehicleThrough your vehicle’s ignition negative ground only Power your scannerFrom a wall outlet From your vehicle’s cigarrette lighter Rear ViewConnect your scanner Connecting the supplied antennaConnecting an external antenna Connecting an external speaker Use extreme caution when installing or removing anListening Safely Set the squelch Set up your scannerTurn on your scanner Scanning overview Basics Listen to preprogrammed frequenciesCommon scanner terms Basics Advanced scanner features Beyond the BasicsChannel storage banks Storing known frequencies into channelsBeyond the Basics Locking out a channel in hold mode Locking out a channel in scanning modeBeyond the Basics Deleting a stored frequency Locking out channelsRestoring all locked-out channels Restoring a locked-out channel in hold modeMemory lock Direct channel access Beyond the Basics Hold/resumeScanning a private bank Beyond the Basics Priority scan Changing the priority channelService scanning Setting a search band Beyond the Basics Band searchData skip Search holdBeyond the Basics Frequency skip Storing search frequenciesDelay Selecting the state Highway patrol alertsHighway patrol/local police scanning State Code Order Press these buttons Action Highway warning alert Setting the alert tone volumeBeyond the Basics Scan hold Adjusting alert Highway patrol priority channelsMuting the alert tone Skip frequenciesTrunked highway frequencies Skywarn About SkywarnNWR Same Programming a Fips code Programming FipsBeyond the Basics Signal Stalker Setting the signal stalker options Beyond the Basics Using signal stalker Setting the squelch Trunk trackingProgramming trunking frequencies Selecting Trunking System Type Programming id scan lists manually Motorola talk groups Edacs talk groupsLTR talk groups Receiving trunked systemsID scan mode ID scan hold modeID search hold mode Direct entry id hold modeID search mode Deleting a stored ID ID monitor modeProgramming scan lists during search Restoring locked-out IDs ID lockoutReviewing ID lockout Trunking frequency conﬁrmation Setting the delay mode for trunking modeSetting priority in trunking mode Moving between scan list memories Multi-trackAbout multi-track Edacs tracking Programming Edacs system frequenciesAFS partial entry Special Edacs featuresBeyond the Basics An Edacs trunked system Edacs ID range search Edacs ID blockoutTracking LTR systems Edacs ScatBeyond the Basics Tracking Motorola systems ﬂeet map programming Preset Fleet Maps E1P1 E1P5 E1P11 Selecting a Preset Fleet Map User-deﬁned ﬂeet mapsFleet Map Size Codes Programming a Hybrid system Size code restrictionsProgramming a user ﬂeet map You can only enter within a range of 5-100 kHz, and 5 or Toggling the status bit Control channel only mode Disconnect tone detect option end code If the scanner receives no data from the PC for more than Cloning your scanner Replacing the fuse in the DC power cord BirdiesBeyond the Basics Resetting your scanner ProperlyFrequently asked questions FAQs Drive by patrol cars but do not hear alarms?Error appears on the display. What does it mean? Speciﬁcations If FrequenciesGlossary Service and repair Care