Radio Shack 20-426 manual Cloning your scanner

Page 76

Beyond the Basics

6.When the scanner has successfully received all data, End appears. If the scanner received an error while receiving data, End, d-Err, and its frame number appear. If the scanner received a communication error while receiving data, C-Err indicates the packet number where the error occurred. If the scanner received a checksum error while receiving data, S-Err indicates the packet number where the error occurred. If the scanner received a length ﬁeld error while receiving data, L-Err indicates the packet number where the error occurred.

cloning your scanner

You can clone all the frequencies, trunking talk groups, and ﬂeet maps programmed in your PRO-2051 to another PRO-2051 using an optional interface cable and software (available at your local RadioShack or www.radioshack.com).

1.Make sure the scanners are turned off and then plug the cable into each scanner’s PC/IF jack.

2.While you press and hold E on both scanners, turn on both scanners.

3.Determine the scanner which has the frequency data that you want to transfer. This one must be set up as the “First Unit”, and the other must be set as the “Clone Unit”.

4.On the scanner that is the “Clone Unit”, press e or d to select CLONE, then press HOLD/RESUME.

5.On the scanner that is the “First Unit”, press e or d to select FirSt, then press HOLD/RESUME. The data transfer begins from the First Unit to the Clone Unit.

During data transfer, SNDFirSt appears when a scanner is sending data and REC CLONE appears when a scanner is receiving data. When the data transfer is complete, donE appears. If the data transfer is not successful, Error appears.

76

Image 76

Contents Pro-2051 1,000-Channel Triple Trunking Mobile/Base Scanner Contents Power your scanner Set up your scannerBasics BasicsAdvanced scanner features Beyond the BasicsScanning a private bank Highway patrol alertsContents Skywarn Signal StalkerWired programming WarrantyYour scanner’s keypad HOLD/RESUMETo Do This Your scanner’s rear view Your scanner’s display TrunkFCC wants you to know Install your scanner Mounting the scanner in your vehicleFrom a wall outlet Power your scannerThrough your vehicle’s ignition negative ground only From your vehicle’s cigarrette lighter Rear ViewConnecting an external antenna Connecting the supplied antennaConnect your scanner Connecting an external speaker Use extreme caution when installing or removing anListening Safely Turn on your scanner Set up your scannerSet the squelch Common scanner terms Basics Listen to preprogrammed frequenciesScanning overview Basics Advanced scanner features Beyond the BasicsChannel storage banks Storing known frequencies into channelsBeyond the Basics Locking out a channel in hold mode Locking out a channel in scanning modeBeyond the Basics Deleting a stored frequency Locking out channelsMemory lock Restoring a locked-out channel in hold modeRestoring all locked-out channels Direct channel access Beyond the Basics Hold/resumeScanning a private bank Beyond the Basics Priority scan Changing the priority channelService scanning Setting a search band Beyond the Basics Band searchData skip Search holdBeyond the Basics Frequency skip Storing search frequenciesDelay Highway patrol/local police scanning Highway patrol alertsSelecting the state State Code Order Press these buttons Action Beyond the Basics Scan hold Setting the alert tone volumeHighway warning alert Adjusting alert Highway patrol priority channelsMuting the alert tone Skip frequenciesTrunked highway frequencies Skywarn About SkywarnNWR Same Programming a Fips code Programming FipsBeyond the Basics Signal Stalker Setting the signal stalker options Beyond the Basics Using signal stalker Setting the squelch Trunk trackingProgramming trunking frequencies Selecting Trunking System Type Programming id scan lists manually Motorola talk groups Edacs talk groupsLTR talk groups Receiving trunked systemsID scan mode ID scan hold modeID search mode Direct entry id hold modeID search hold mode Programming scan lists during search ID monitor modeDeleting a stored ID Reviewing ID lockout ID lockoutRestoring locked-out IDs Setting priority in trunking mode Setting the delay mode for trunking modeTrunking frequency conﬁrmation Moving between scan list memories Multi-trackAbout multi-track Edacs tracking Programming Edacs system frequenciesBeyond the Basics An Edacs trunked system Special Edacs featuresAFS partial entry Edacs ID range search Edacs ID blockoutTracking LTR systems Edacs ScatBeyond the Basics Tracking Motorola systems ﬂeet map programming Preset Fleet Maps E1P1 E1P5 E1P11 Selecting a Preset Fleet Map User-deﬁned ﬂeet mapsFleet Map Size Codes Programming a user ﬂeet map Size code restrictionsProgramming a Hybrid system You can only enter within a range of 5-100 kHz, and 5 or Toggling the status bit Control channel only mode Disconnect tone detect option end code If the scanner receives no data from the PC for more than Cloning your scanner Replacing the fuse in the DC power cord BirdiesBeyond the Basics Resetting your scanner ProperlyFrequently asked questions FAQs Drive by patrol cars but do not hear alarms?Error appears on the display. What does it mean? Speciﬁcations If FrequenciesGlossary Service and repair Care