Cisco Systems R2001120402, UCS C200 M1 manual RAID Controller Cabling

Page 99

Appendix C RAID Controller Considerations

Enabling the Mezzanine Card RAID Controller in the BIOS

Enabling the Mezzanine Card RAID Controller in the BIOS

When using the supported mezzanine-style RAID controller card, you must enable the ICH10R controller in Enhanced mode.

Step 1 Make sure that a RAID cable is attached between the mezzanine card and the disk backplane. Step 2 Boot the server and press F2 when prompted to enter the BIOS Setup utility.

Step 3 Select the Advanced tab, then Mass Storage Controllers Configuration.

Step 4 Set Onboard SATA Controller to Enabled.

Step 5 Set SATA Mode to Enhanced.

Step 6 Press F10 to save your changes and exit the BIOS Setup utility.

Step 7 To set up a RAID configuration when using the mezzanine card, boot the server and press Ctrl-Cwhen prompted to start the WebBIOS utility.

RAID Controller Cabling

The possible RAID controller connectors in this server are shown in Figure C-1. The blue line indicates the recommended cable routing path from the backplane to the possible controller locations.

Note The Cisco UCS C200 SFF server is shown, with an eight-drive backplane. The LFF server has a four-drive backplane.

Figure C-1 RAID Controller Connectors

	4
1
2	3
2

					332177

1			Drive backplane	3	Mezzanine card connector(s)

2			Integrated RAID connector on	4	LSI MegaRAID PCIe card connectors
			motherboard

					Cisco UCS C200 Server Installation and Service Guide
					Cisco UCS C200 Server Installation and Service Guide

	OL-20732-02							C-3
	OL-20732-02							C-3

Image 99

Contents Cisco UCS C200 Server Installation and Service Guide Page N T E N T S Status LEDs AC Power Cord Illustrations OL-20732-02 Related Documentation AudienceOrganization Bewaar Deze Instructies ConventionsConservez CES Informations Guarde Estas Instrucciones GEM Disse Anvisninger Xii Obtaining Documentation and Submitting a Service Request Xiv Overview Optional DVD module Rear Panel Features Feature or Component Cisco UCS C200 Server LFF RAID = redundant array of independent disks Installing the Server Unpacking and Inspecting the Server Shipping Box ContentsInstallation Guidelines Preparing for InstallationSlide Rail Adjustment Range Rack RequirementsRequired Equipment Installing the Server Into a Rack Attaching a Slide-Rail Assembly Attaching Mounting Brackets to the Server Attaching the Cable Management Arm Connecting and Powering On the Server Standalone Mode Initial Server SetupOL-20732-02 Cisco UCS C200 Server Installation and Service Guide NIC Modes and NIC Redundancy Settings Updating the Bios and Cimc Firmware System Bios and Cimc FirmwareAccessing the System Bios Motherboard Jumpers Service Jumper LocationsUsing the Bios Recovery Jumper J1E5 to Recover Corrupt Bios Clearing the Cimc Admin Password Using Jumper J45 Using the Clear Cmos Jumper J1E6 Clearing the Bios Admin Password Using Jumper J1E4 OL-20732-02 Server Configuration Utility Server Monitoring and Management ToolsCisco Integrated Management Interface Cimc Front Panel LEDs Status LEDsLED Name State Rear Panel LEDs CPU fault Off-All CPUs are operating properlyLED Name State LED Name State Shutting Down and Powering Off the Server Preparing for Component InstallationRemoving and Replacing the Server in a Rack Removing the Top Cover of the Server Removing and Replacing the Server Top CoverRemoving the Front Cover of the Server 6shows the Large Form Factor LFF version of the server Replaceable Component LocationsReplaceable Component Locations, Small Form Factor Top View Installing or Replacing Components Maintaining the Server Installing or Replacing Components 282338 Alternate Front Panel Module Cable Routing Installing Hard Drives or Solid State Drives HDD01 HDD02 HDD03 HDD04 HDD01 HDD02 HDD03 HDD04 HDD05 HDD06 HDD07 HDD08 PSU2 PSU1 Installing Power SuppliesInstalling a Fan Tray 15 Removing and Replacing a Fan Tray Memory Performance Guidelines and Population Rules Installing DIMMsMemory Population Rules Low-Voltage Dimm Considerations Generation M2 Only Dimm Installation Procedure 17 Removing and Replacing Memory Modules Installing CPUs and Heatsinks 18 Removing and Replacing CPUs and Heatsinks Installing a Motherboard Cmos Battery 19 Removing and Replacing a Motherboard Cmos Battery Installing a Trusted Platform ModuleTPM Replacing a PCIe Riser Card Assembly Replacing a PCIe Card 21 Removing and Replacing a PCIe Riser Card AssemblyReplacement Procedure PCIe Slot How to Identify Which Power Supply Model is in Your Server Resolving Insufficient Memory Space to Execute Option ROMs Resolving Insufficient 16-Bit I/O Space Replacing an LSIiBBU06 BBU Replacing an LSI MegaRAID Battery Backup Unit24 Removing and Replacing an LSIiBBU06 BBU 25 Replacing a Mounting Bracket for the LSIiBBU08 BBU Replacing an LSIiBBU08 BBUScrews 27 Removing and Replacing an LSIiBBU06 BBU Installing a Mezzanine Card Mezzanine card retaining posts three Physical Specifications Technical SpecificationsPower Specifications Environmental SpecificationsKVM Cable Cable and Power Cord SpecificationsDescription Feet Meters Illustration Supported Power Cords and PlugsThis section contains the AC power cord illustrations AC Power Cord IllustrationsCAB-9K10A-EU CAB-9K10A-SW CAB-N5K6A-NA CAB-9K12A-NA OL-20732-02 Supported RAID Controllers and Required Cables RAID Controller ConsiderationsR200-SASCBL3 RAID Controller Cabling Enabling the Mezzanine Card RAID Controller in the BiosHow to Determine Which Controller Is in Your Server Cisco UCS C200 LFF Server CablingCisco UCS C200 SFF Server Cabling How To Launch Option ROM-Based Controller Utilities From your For More Information OL-20732-02 Installation for Cisco UCS Integration OL-20732-02