Cisco Systems R2001120402, UCS C200 M1 manual Screws

Page 83

Chapter 3 Maintaining the Server

Installing or Replacing Components

Figure 3-26 Replacing a Mounting Bracket for the LSIiBBU08 BBU (Enlarged)

Screws

331002

Step 2 Install the new LSIiBBU08 BBU:

Note The LSIiBBU08 BBU requires minimum LSI MegaRAID card firmware 2.120.133.1322 or later to be recognized. You can use the Cisco Host Upgrade Utility to upgrade your LSI MegaRAID card firmware. Obtain the Cisco Host Upgrade Utility 1.4.1 or later package (including drivers) by navigating from the Cisco.com software download site: http://www.cisco.com/cisco/software/navigator.html

a.Install the BBU cable from the LSI controller card to socket J2 on the new BBU.

Note Align the arrow-mark on the cable connector with the arrow-mark on the socket to avoid damaging the connector pins.

b.Place the new BBU over the new BBU bracket on the fan tray and align the two screw-holes in the BBU with the two preinstalled standoffs on the bracket.

c.Install the two securing screws that hold the BBU to the BBU bracket.

		Cisco UCS C200 Server Installation and Service Guide
		Cisco UCS C200 Server Installation and Service Guide
	OL-20732-02			3-43
	OL-20732-02			3-43

Image 83

Contents Cisco UCS C200 Server Installation and Service Guide Page N T E N T S Status LEDs AC Power Cord Illustrations OL-20732-02 Organization Related DocumentationAudience Bewaar Deze Instructies ConventionsConservez CES Informations Guarde Estas Instrucciones GEM Disse Anvisninger Xii Obtaining Documentation and Submitting a Service Request Xiv Overview Optional DVD module Rear Panel Features Feature or Component Cisco UCS C200 Server LFF RAID = redundant array of independent disks Installing the Server Unpacking and Inspecting the Server Shipping Box ContentsInstallation Guidelines Preparing for InstallationRequired Equipment Slide Rail Adjustment RangeRack Requirements Installing the Server Into a Rack Attaching a Slide-Rail Assembly Attaching Mounting Brackets to the Server Attaching the Cable Management Arm Connecting and Powering On the Server Standalone Mode Initial Server SetupOL-20732-02 Cisco UCS C200 Server Installation and Service Guide NIC Modes and NIC Redundancy Settings Updating the Bios and Cimc Firmware System Bios and Cimc FirmwareAccessing the System Bios Motherboard Jumpers Service Jumper LocationsUsing the Bios Recovery Jumper J1E5 to Recover Corrupt Bios Clearing the Cimc Admin Password Using Jumper J45 Using the Clear Cmos Jumper J1E6 Clearing the Bios Admin Password Using Jumper J1E4 OL-20732-02 Cisco Integrated Management Interface Cimc Server Configuration UtilityServer Monitoring and Management Tools Front Panel LEDs Status LEDsLED Name State Rear Panel LEDs CPU fault Off-All CPUs are operating properlyLED Name State LED Name State Shutting Down and Powering Off the Server Preparing for Component InstallationRemoving and Replacing the Server in a Rack Removing the Top Cover of the Server Removing and Replacing the Server Top CoverRemoving the Front Cover of the Server 6shows the Large Form Factor LFF version of the server Replaceable Component LocationsReplaceable Component Locations, Small Form Factor Top View Installing or Replacing Components Maintaining the Server Installing or Replacing Components 282338 Alternate Front Panel Module Cable Routing Installing Hard Drives or Solid State Drives HDD01 HDD02 HDD03 HDD04 HDD01 HDD02 HDD03 HDD04 HDD05 HDD06 HDD07 HDD08 PSU2 PSU1 Installing Power SuppliesInstalling a Fan Tray 15 Removing and Replacing a Fan Tray Memory Performance Guidelines and Population Rules Installing DIMMsMemory Population Rules Low-Voltage Dimm Considerations Generation M2 Only Dimm Installation Procedure 17 Removing and Replacing Memory Modules Installing CPUs and Heatsinks 18 Removing and Replacing CPUs and Heatsinks Installing a Motherboard Cmos Battery 19 Removing and Replacing a Motherboard Cmos Battery Installing a Trusted Platform ModuleTPM Replacing a PCIe Riser Card Assembly Replacing a PCIe Card 21 Removing and Replacing a PCIe Riser Card AssemblyReplacement Procedure PCIe Slot How to Identify Which Power Supply Model is in Your Server Resolving Insufficient Memory Space to Execute Option ROMs Resolving Insufficient 16-Bit I/O Space Replacing an LSIiBBU06 BBU Replacing an LSI MegaRAID Battery Backup Unit24 Removing and Replacing an LSIiBBU06 BBU 25 Replacing a Mounting Bracket for the LSIiBBU08 BBU Replacing an LSIiBBU08 BBUScrews 27 Removing and Replacing an LSIiBBU06 BBU Installing a Mezzanine Card Mezzanine card retaining posts three Physical Specifications Technical SpecificationsPower Specifications Environmental SpecificationsKVM Cable Cable and Power Cord SpecificationsDescription Feet Meters Illustration Supported Power Cords and PlugsThis section contains the AC power cord illustrations AC Power Cord IllustrationsCAB-9K10A-EU CAB-9K10A-SW CAB-N5K6A-NA CAB-9K12A-NA OL-20732-02 Supported RAID Controllers and Required Cables RAID Controller ConsiderationsR200-SASCBL3 RAID Controller Cabling Enabling the Mezzanine Card RAID Controller in the BiosCisco UCS C200 SFF Server Cabling How to Determine Which Controller Is in Your ServerCisco UCS C200 LFF Server Cabling How To Launch Option ROM-Based Controller Utilities From your For More Information OL-20732-02 Installation for Cisco UCS Integration OL-20732-02