Yamaha Yamaha Robot Controller CC-Link Unit, RCX Series CC-Link compatible module specifications

Page 71

5. CC-Link compatible module specifications

The CC-Link compatible module with the label is compatible with CC-Link Ver. 1.10. Limits on the station-to-station cable length, etc., can be eased by using the Ver. 1.10 compatible CC-Link cable. Refer to the master station PLC instruction manual compat- ible with Ver. 1.10.

c CAUTION

For the names and description of remote input/output signals and remote registers, refer to the tables shown in "1. Profile" and "2. Details of remote input/output signals" in this chapter.

c CAUTION

The specifications and appearance are subject to change without prior notice.

Specification item

 

 

CC-Link compatible module

 

 

 

 

Target controller

RCX Series controller

 

Remote station type

Remote device station

 

Number of occupied stations

Fixed to four stations

 

Station No. setting

1 to 61 (rotary switch)

 

Communication speed setting

10M / 5M / 2.5M / 625K / 156Kbps (rotary switch)

Number of CC-Link input/output points *1)

Remote

 

Dedicated input

: 16 points

 

 

input/output

 

 

(11 points are currently used.)

 

 

 

General-purpose input

: 96 points

 

 

 

 

 

 

 

 

Dedicated output

: 16 points

 

 

 

 

(11 points are currently used.)

 

 

 

General-purpose output : 96 points

 

 

 

 

 

 

Remote

 

Dedicated input

: 2 words

 

register

 

General-purpose input

: 14 words

 

 

 

 

 

 

 

 

 

 

 

Dedicated output

: 2 words

 

 

 

General-purpose output : 14 words

Monitor LED

RUN, ERRL, SD, RD

 

 

 

 

 

 

*1) Controller's I/O update intervals are 10ms at shortest, but actual I/O update intervals change depending on the update time for the master station.

5

Specifications

5-17

Page 70 Page 72
Image 71
Page 70 Page 72
Contents Unit Page Introduction Precautions for design Safety Precautions Always read before starting usePrecautions for wiring Precautions for installationPrecautions for disposal Precautions for starting and maintenanceWarranty description WarrantyMemo Contents Appendix TroubleshootingSpecifications Outline Memo Emulated serialization on parallel DIO FeaturesWiring saving PLC MechanismCC-Link system cable terminals Station No. setting switch LSB 1st digitStation No. setting switch MSB 2nd digit Communication speed switch BPSA1SHCPU Assignment of CC-Link compatible I/OPLC Outline Outline Memo Connection Memo Operation Confirming the CC-Link compatible module settingsSaving the robot controller data Installing the CC-Link compatible moduleResponse when starting the robot controller ProcedureSetting the station No Setting the CC-Link compatible moduleProcedures Setting the communication speedMounting the ferrite core Noise measuresTesting the line from the master station PLC Connecting to the CC-Link systemParameter Meaning Parameter setting for CC-Link serial I/O boardType Display Meaning Parameter setting for CC-Link serial I/O boardPress the F Edit key Memo Communication Memo When connection to CC-Link system is correctly established State when robot controller power is turned onInitial data process master station PLC side Initial process for connecting to CC-Link systemInitial data process Receiving data Communication with master station PLCTransmitting data Direct connection by emulated serialization on parallel DIO Direct connection from SI n to do n Direct connection by emulated serialization on parallel DIODirect connection from SO n to DI n Direct connection by emulated serialization on parallel DReferring to the data from the programming unit Referring to communication dataTroubleshooting Memo Confirmation details Check Items to confirm before starting up CC-Link systemRUN Errl SD RD Meanings of LEDs on CC-Link compatible moduleConfirmation item TroubleshootingProgramming unit error display confirmation CC-Link compatible module LED confirmation Confirmation from master station PLC Emg.stop on Error messages relating to CC-LinkMemo Specifications Memo Profile Remote registers Device No Signal name Details RXn0 Details of remote input/output signalsDetails of remote input/output signals Details of remote input/output signals Initial data process for CC-Link connection Dedicated input/output signal timing chartServo on process from emergency stop status Initial servo on process after power onServo on and emergency stop Shift to emergency stopProgram execution process SpecificationsAuto mode changeover process Program reset processStopping with program interlock Program stop process using interlock inputDetails of sample Sample programBit information used Robot program data assignment Variables usedPoints used X1FF PLC data assignmentGosub *PLACE Robot program 1st unit’s RCX40 2nd unit’s RCX142X0F From PLC programRET From H0 Set initial data process complete flag OFF Communication speed setting CC-Link compatible module specificationsMemo Appendix Memo Term definition Unit
Top Page Image Contents