Siemens OSM technical specifications Properties of the ESM TP80

Page 22

Introduction

Properties of the ESM TP80
Electrical ports	8 x 10/100 Mbps autonegotiation ports
	TP connectors (RJ-45 jacks)
Optical ports	none
Maximum distance between two ESM	100 m
TP80 modules
Maximum ring span with 50 ESM TP80	5 km
modules
Digital Inputs	8 x DC 24V

Note

Industrial Ethernet OSM TP80 is available in two versions:

•ESM TP80 with eight digital inputs:

The eight digital inputs are connected over two plug-in 6-pin terminal blocks on the top of the device. To display the status of these inputs using the 8 device LEDs, there is an additional display mode known as the "Input Status" that is selected using a third mode LED.

•ESM TP80 without digital inputs:

There are no digital inputs and the "Input Status" display mode is not available. The operating states are displayed by 2 mode LEDs.

18	Industrial Ethernet OSM/ESM
	C79000-Z8976-C068-10

Image 22

Contents Simatic NET Classification of Safety-Related Notices Copyright Siemens AG 2000/02, All rights reservedQualified Personnel Safety Instructions Regarding your ProductTrademarks Correct Usage of Hardware ProductsCorrect Usage of Software Products Prior to StartupPurpose of the Operating Instructions Installing an OSM/ESMPreface PackageFurther Documentation Validity of the Operating InstructionsFinding Information Personnel Qualification Requirements Guide to the ManualAudience Standards and ApprovalsContents Introduction Introduction OSM ITP62 Overview of the Variants of the OSM/ESMPossible Attachments Properties of the OSM ITP62 OSM ITP62-LD OSM ITP62-LDProperties of the OSM ITP62-LD ITP62-LDOSM ITP53 OSM ITP53Properties of the OSM ITP53 ESM ITP80 ESM ITP80Properties of the ESM ITP80 OSM TP62 OSM TP62Properties of the OSM TP62 ESM TP80 ESM TP80Properties of the ESM TP80 OSM BC08 OSM BC08Properties of the OSM BC08 OSM TP22 OSM TP22Properties of the OSM TP22 ESM TP40 ESM TP40Properties of the ESM TP40 Functions Simple Network Configuration and Network ExpansionLimitation of Errors to the Network Segment Affected Increased Network PerformanceDeleting Addresses Setting the Transmission Rate, AutonegotiationPackets with the Vlan Priority Tag Functions Network Topologies with OSM/ESM Bus Structure Bus with OSMBus with ESMs Redundant Ring Structure Redundant Ring Structure with OSMsESM in RM mode Redundant Coupling of Network Segments OSM/ESM Simultaneous Standby and Redundancy Manager Operation Port Assignment in the Standby ModeReplacing the Standby Master During Operation OSM RM mode Compatibility of OSM Version 2/ESM with OSM/ORM Version CompatibilityRing with OSM Version 2 as Redundancy Manager Redundant Coupling of Rings Standby Master Slave OSM Coupling Network Segments RM mode OSMInterfaces, Displays and Operator Controls ITP Ports ITP/TP PortsTP Ports Link Control Autonegotiation ModeProperties of the TP/ITP Ports Auto Polarity ExchangeInterfaces, Displays and Operator Controls FO Ports Standby-Sync Port Serial Interface PinoutTerminal Block for the Power Supply and Signaling Contact Signaling Contact Power SupplyRM Mode additional OSM/ESM in the Standby Mode Digital Inputs Input voltage must not exceed +30V DC or fall below -30V DCLED Display Status Fault red LEDDisplays and Operator Controls Stby Standby green LEDRM Redundancy Manager green LED LED Power Display mode MeaningFault Mask Port LEDs DisplayFull duplex Port LED Two-Pin DIP Switch DIP SwitchesSelect/Set Button Installation, Commissioning, Cleaning Maintenance Do not install damaged components Unpacking, Checking the ConsignmentInstallation PreparationsInstalling the OSM on a DIN Standard Rail Standard Rail MountingRemoving from a Standard Rail Removing from the Standard RailInstallation on a Simatic S7-300 Rail Installation on the S7-300 RailInstallation in Pairs in the 19 Cubicle Installation in the 19 CubicleWall Mounting Wall MountingWall Mounting Cleaning Maintenance Firmware Update Specifying the keyword OSM FirmwareFirmware Update Firmware Update Firmware Update Firmware Update Technical Specifications PortsTechnical Specifications Permitted Cable Lengths Switching Properties of OSM/ESMCascading Depth Mechanical Design Only horizontal installationPermitted Ambient Conditions/EMC PermittedConsignment / Order Numbers Accessories Product name Standards and ApprovalsCE Mark UL Approval Area of ApplicationApproval for Australia CSA CertificationFM Approval Adherence to Installation Instructions Fault Mask Filtering ITP Port GlossaryLink Control LatencyTP Port Industrial Ethernet OSM/ESM C79000-Z8976-C068-10 References Http//www4.ad.siemens.de/view/cs/de/8677203Industrial Ethernet OSM/ESM C79000-Z8976-C068-10 Index Ambient conditions, permittedIndex