Siemens OSM, ESM technical specifications Cleaning

Page 75

Installation, Commissioning, Cleaning and Maintenance

5.3Cleaning

If you need to clean the OSM/ESM, use a dry cloth only.

Industrial Ethernet OSM/ESM	71
C79000-Z8976-C068-10

Image 75

Contents Simatic NET Copyright Siemens AG 2000/02, All rights reserved Classification of Safety-Related NoticesCorrect Usage of Hardware Products Safety Instructions Regarding your ProductTrademarks Qualified PersonnelPrior to Startup Correct Usage of Software ProductsPackage Installing an OSM/ESMPreface Purpose of the Operating InstructionsValidity of the Operating Instructions Further DocumentationFinding Information Standards and Approvals Guide to the ManualAudience Personnel Qualification RequirementsContents Introduction Introduction Overview of the Variants of the OSM/ESM OSM ITP62Possible Attachments Properties of the OSM ITP62 OSM ITP62-LD OSM ITP62-LDITP62-LD Properties of the OSM ITP62-LDOSM ITP53 OSM ITP53Properties of the OSM ITP53 ESM ITP80 ESM ITP80Properties of the ESM ITP80 OSM TP62 OSM TP62Properties of the OSM TP62 ESM TP80 ESM TP80Properties of the ESM TP80 OSM BC08 OSM BC08Properties of the OSM BC08 OSM TP22 OSM TP22Properties of the OSM TP22 ESM TP40 ESM TP40Properties of the ESM TP40 Increased Network Performance Simple Network Configuration and Network ExpansionLimitation of Errors to the Network Segment Affected FunctionsSetting the Transmission Rate, Autonegotiation Deleting AddressesPackets with the Vlan Priority Tag Functions Network Topologies with OSM/ESM Bus with OSM Bus StructureBus with ESMs Redundant Ring Structure with OSMs Redundant Ring StructureESM in RM mode Redundant Coupling of Network Segments OSM/ESM Port Assignment in the Standby Mode Simultaneous Standby and Redundancy Manager OperationReplacing the Standby Master During Operation OSM RM mode Compatibility Compatibility of OSM Version 2/ESM with OSM/ORM VersionRing with OSM Version 2 as Redundancy Manager Redundant Coupling of Rings Standby Master Slave OSM Coupling Network Segments OSM RM modeInterfaces, Displays and Operator Controls ITP/TP Ports ITP PortsTP Ports Auto Polarity Exchange Autonegotiation ModeProperties of the TP/ITP Ports Link ControlInterfaces, Displays and Operator Controls FO Ports Standby-Sync Port Pinout Serial InterfaceTerminal Block for the Power Supply and Signaling Contact Power Supply Signaling ContactRM Mode additional OSM/ESM in the Standby Mode Input voltage must not exceed +30V DC or fall below -30V DC Digital InputsStby Standby green LED Fault red LEDDisplays and Operator Controls LED Display StatusRM Redundancy Manager green LED Display mode Meaning LED PowerFault Mask Display Port LEDsFull duplex Port LED DIP Switches Two-Pin DIP SwitchSelect/Set Button Installation, Commissioning, Cleaning Maintenance Unpacking, Checking the Consignment Do not install damaged componentsPreparations InstallationStandard Rail Mounting Installing the OSM on a DIN Standard RailRemoving from the Standard Rail Removing from a Standard RailInstallation on the S7-300 Rail Installation on a Simatic S7-300 RailInstallation in the 19 Cubicle Installation in Pairs in the 19 CubicleWall Mounting Wall MountingWall Mounting Cleaning Maintenance Specifying the keyword OSM Firmware Firmware UpdateFirmware Update Firmware Update Firmware Update Firmware Update Ports Technical SpecificationsTechnical Specifications Switching Properties of OSM/ESM Permitted Cable LengthsCascading Depth Permitted Only horizontal installationPermitted Ambient Conditions/EMC Mechanical DesignConsignment / Order Numbers Accessories Standards and Approvals Product nameCE Mark CSA Certification Area of ApplicationApproval for Australia UL ApprovalFM Approval Adherence to Installation Instructions Glossary Fault Mask Filtering ITP PortLatency Link ControlTP Port Industrial Ethernet OSM/ESM C79000-Z8976-C068-10 Http//www4.ad.siemens.de/view/cs/de/8677203 ReferencesIndustrial Ethernet OSM/ESM C79000-Z8976-C068-10 Ambient conditions, permitted IndexIndex