Siemens ESM technical specifications Properties of the OSM ITP62

Page 12

Introduction

Properties of the OSM ITP62
Electrical ports	6 x 10/100 Mbps
	autonegotiation/autocrossover ports
	ITP connectors (sub-D 9-pin female)

Optical ports	2 x 100 Mbps FO ports (full duplex)
	BFOC female connectors
Maximum distance between two OSMs	3000 m (multimode graded-index fiber)

Maximum ring span with 50 OSMs	150 km
Digital Inputs	8 x DC 24V

Note

Industrial Ethernet OSM ITP62 is available in two versions:

•OSM ITP62 with eight digital inputs:

The eight digital inputs are connected over two plug-in 6-pin terminal blocks on the top of the device. To display the status of these inputs using the eight device LEDs, there is an additional display mode known as the "Input Status" that is selected using a third mode LED.

•OSM ITP62 without digital inputs:

There are no digital inputs and the "Input Status" display mode is not available. The operating states are displayed by two mode LEDs.

8	Industrial Ethernet OSM/ESM
	C79000-Z8976-C068-10

Image 12

Contents Simatic NET Classification of Safety-Related Notices Copyright Siemens AG 2000/02, All rights reservedSafety Instructions Regarding your Product TrademarksQualified Personnel Correct Usage of Hardware ProductsCorrect Usage of Software Products Prior to StartupInstalling an OSM/ESM PrefacePurpose of the Operating Instructions PackageValidity of the Operating Instructions Further DocumentationFinding Information Guide to the Manual AudiencePersonnel Qualification Requirements Standards and ApprovalsContents Introduction Introduction Overview of the Variants of the OSM/ESM OSM ITP62Possible Attachments Properties of the OSM ITP62 OSM ITP62-LD OSM ITP62-LDProperties of the OSM ITP62-LD ITP62-LDOSM ITP53 OSM ITP53Properties of the OSM ITP53 ESM ITP80 ESM ITP80Properties of the ESM ITP80 OSM TP62 OSM TP62Properties of the OSM TP62 ESM TP80 ESM TP80Properties of the ESM TP80 OSM BC08 OSM BC08Properties of the OSM BC08 OSM TP22 OSM TP22Properties of the OSM TP22 ESM TP40 ESM TP40Properties of the ESM TP40 Simple Network Configuration and Network Expansion Limitation of Errors to the Network Segment AffectedFunctions Increased Network PerformanceSetting the Transmission Rate, Autonegotiation Deleting AddressesPackets with the Vlan Priority Tag Functions Network Topologies with OSM/ESM Bus Structure Bus with OSMBus with ESMs Redundant Ring Structure Redundant Ring Structure with OSMsESM in RM mode Redundant Coupling of Network Segments OSM/ESM Port Assignment in the Standby Mode Simultaneous Standby and Redundancy Manager OperationReplacing the Standby Master During Operation OSM RM mode Compatibility of OSM Version 2/ESM with OSM/ORM Version CompatibilityRing with OSM Version 2 as Redundancy Manager Redundant Coupling of Rings Standby Master Slave OSM Coupling Network Segments RM mode OSMInterfaces, Displays and Operator Controls ITP/TP Ports ITP PortsTP Ports Autonegotiation Mode Properties of the TP/ITP PortsLink Control Auto Polarity ExchangeInterfaces, Displays and Operator Controls FO Ports Standby-Sync Port Serial Interface PinoutTerminal Block for the Power Supply and Signaling Contact Power Supply Signaling ContactRM Mode additional OSM/ESM in the Standby Mode Digital Inputs Input voltage must not exceed +30V DC or fall below -30V DCFault red LED Displays and Operator ControlsLED Display Status Stby Standby green LEDRM Redundancy Manager green LED LED Power Display mode MeaningFault Mask Port LEDs DisplayFull duplex Port LED Two-Pin DIP Switch DIP SwitchesSelect/Set Button Installation, Commissioning, Cleaning Maintenance Do not install damaged components Unpacking, Checking the ConsignmentInstallation PreparationsInstalling the OSM on a DIN Standard Rail Standard Rail MountingRemoving from a Standard Rail Removing from the Standard RailInstallation on a Simatic S7-300 Rail Installation on the S7-300 RailInstallation in Pairs in the 19 Cubicle Installation in the 19 CubicleWall Mounting Wall MountingWall Mounting Cleaning Maintenance Firmware Update Specifying the keyword OSM FirmwareFirmware Update Firmware Update Firmware Update Firmware Update Technical Specifications PortsTechnical Specifications Switching Properties of OSM/ESM Permitted Cable LengthsCascading Depth Only horizontal installation Permitted Ambient Conditions/EMCMechanical Design PermittedConsignment / Order Numbers Accessories Standards and Approvals Product nameCE Mark Area of Application Approval for AustraliaUL Approval CSA CertificationFM Approval Adherence to Installation Instructions Fault Mask Filtering ITP Port GlossaryLatency Link ControlTP Port Industrial Ethernet OSM/ESM C79000-Z8976-C068-10 References Http//www4.ad.siemens.de/view/cs/de/8677203Industrial Ethernet OSM/ESM C79000-Z8976-C068-10 Index Ambient conditions, permittedIndex