Siemens ESM, OSM technical specifications Correct Usage of Software Products, Prior to Startup

Page 4

Correct Usage of Software Products

Please note the following regarding the correct usage of software products:

Caution

This software may only be used for the applications described in the catalog or the technical description, and only in connection with devices or software products from other manufacturers which have been approved or recommended by Siemens.

Before you use the supplied sample programs or programs you have written yourself, make certain that no injury to persons nor damage to equipment can result in your plant or process.

Prior to Startup

Before putting the product into operation, note the following warning:

Caution

Prior to startup you must observe the instructions in the relevant documentation. For ordering data of the documentation please refer to the catalogs or contact your local SIEMENS representative.

Copyright Siemens AG 2000/02, All rights reserved

The reproduction, transmission or use of this document or its contents is not permitted without express written authority. Offenders will be liable for damages. All rights, including rights created by patent grant or registration of a utility or design, are reserved.

Siemens AG

Automation and Drives

Postfach 48 48, D-90327 Nuernberg

Disclaimer

We have checked the contents of this manual for agreement with the hardware and software described. Since deviations cannot be precluded entirely, we cannot guarantee full agreement. However, the data in this manual are reviewed regularly and any necessary corrections included in subsequent editions. Suggestions for improvement are welcome.

C79000-Z8976-C068-10

© Siemens AG 2001/2003 Technical data subject to change.

Siemens Aktiengesellschaft

Printed in the Federal Republic of Germany

Image 4
Contents Simatic NET Classification of Safety-Related Notices Copyright Siemens AG 2000/02, All rights reservedSafety Instructions Regarding your Product TrademarksQualified Personnel Correct Usage of Hardware ProductsCorrect Usage of Software Products Prior to StartupInstalling an OSM/ESM PrefacePurpose of the Operating Instructions PackageFurther Documentation Validity of the Operating InstructionsFinding Information Guide to the Manual AudiencePersonnel Qualification Requirements Standards and ApprovalsContents Introduction Introduction OSM ITP62 Overview of the Variants of the OSM/ESMPossible Attachments Properties of the OSM ITP62 OSM ITP62-LD OSM ITP62-LDProperties of the OSM ITP62-LD ITP62-LDOSM ITP53 OSM ITP53Properties of the OSM ITP53 ESM ITP80 ESM ITP80Properties of the ESM ITP80 OSM TP62 OSM TP62Properties of the OSM TP62 ESM TP80 ESM TP80Properties of the ESM TP80 OSM BC08 OSM BC08Properties of the OSM BC08 OSM TP22 OSM TP22Properties of the OSM TP22 ESM TP40 ESM TP40Properties of the ESM TP40 Simple Network Configuration and Network Expansion Limitation of Errors to the Network Segment AffectedFunctions Increased Network PerformanceDeleting Addresses Setting the Transmission Rate, AutonegotiationPackets with the Vlan Priority Tag Functions Network Topologies with OSM/ESM Bus Structure Bus with OSMBus with ESMs Redundant Ring Structure Redundant Ring Structure with OSMsESM in RM mode Redundant Coupling of Network Segments OSM/ESM Simultaneous Standby and Redundancy Manager Operation Port Assignment in the Standby ModeReplacing the Standby Master During Operation OSM RM mode Compatibility of OSM Version 2/ESM with OSM/ORM Version CompatibilityRing with OSM Version 2 as Redundancy Manager Redundant Coupling of Rings Standby Master Slave OSM Coupling Network Segments RM mode OSMInterfaces, Displays and Operator Controls ITP Ports ITP/TP PortsTP Ports Autonegotiation Mode Properties of the TP/ITP PortsLink Control Auto Polarity ExchangeInterfaces, Displays and Operator Controls FO Ports Standby-Sync Port Serial Interface PinoutTerminal Block for the Power Supply and Signaling Contact Signaling Contact Power SupplyRM Mode additional OSM/ESM in the Standby Mode Digital Inputs Input voltage must not exceed +30V DC or fall below -30V DCFault red LED Displays and Operator ControlsLED Display Status Stby Standby green LEDRM Redundancy Manager green LED LED Power Display mode MeaningFault Mask Port LEDs DisplayFull duplex Port LED Two-Pin DIP Switch DIP SwitchesSelect/Set Button Installation, Commissioning, Cleaning Maintenance Do not install damaged components Unpacking, Checking the ConsignmentInstallation PreparationsInstalling the OSM on a DIN Standard Rail Standard Rail MountingRemoving from a Standard Rail Removing from the Standard RailInstallation on a Simatic S7-300 Rail Installation on the S7-300 RailInstallation in Pairs in the 19 Cubicle Installation in the 19 CubicleWall Mounting Wall MountingWall Mounting Cleaning Maintenance Firmware Update Specifying the keyword OSM FirmwareFirmware Update Firmware Update Firmware Update Firmware Update Technical Specifications PortsTechnical Specifications Permitted Cable Lengths Switching Properties of OSM/ESMCascading Depth Only horizontal installation Permitted Ambient Conditions/EMCMechanical Design PermittedConsignment / Order Numbers Accessories Product name Standards and ApprovalsCE Mark Area of Application Approval for AustraliaUL Approval CSA CertificationFM Approval Adherence to Installation Instructions Fault Mask Filtering ITP Port GlossaryLink Control LatencyTP Port Industrial Ethernet OSM/ESM C79000-Z8976-C068-10 References Http//www4.ad.siemens.de/view/cs/de/8677203Industrial Ethernet OSM/ESM C79000-Z8976-C068-10 Index Ambient conditions, permittedIndex