Siemens ESM, OSM technical specifications Standards and Approvals, Product name, CE Mark

Page 88

Standards and Approvals	8

Product name:

The OSM/ESM products listed below, comply with the following standards and directives if they have the corresponding symbols on the type plate:

Industrial Ethernet OSM ITP62 with digital inputs Industrial Ethernet OSM ITP62 without digital inputs Industrial Ethernet OSM ITP62-LD with digital inputs Industrial Ethernet OSM ITP62-LD without digital inputs Industrial Ethernet OSM ITP53 with digital inputs Industrial Ethernet OSM ITP53 without digital inputs Industrial Ethernet OSM ITP80 with digital inputs Industrial Ethernet OSM ITP80 without digital inputs Industrial Ethernet OSM TP62 with digital inputs Industrial Ethernet OSM TP62 without digital inputs Industrial Ethernet OSM TP80 with digital inputs Industrial Ethernet OSM TP80 without digital inputs Industrial Ethernet OSM TP22 with digital inputs Industrial Ethernet OSM TP40 with digital inputs Industrial Ethernet OSM BC08 with digital inputs

6GK1105-2AA10 6GK1105-2AA00 6GK1105-2AC10 6GK1105-2AC00 6GK1105-2AD10 6GK1105-2AD00 6GK1105-3AA10 6GK1105-3AA00 6GK1105-2AB10 6GK1105-2AB00 6GK1105-3AB10 6GK1105-3AB00 6GK1105-2AE00 6GK1105-3AC00 6GK1105-4AA00

CE Mark

SIMATIC NET OSMs/ESMs meet the requirements of the following EU directives:

Directive 89/336/EEC “Electromagnetic Compatibility" (EMC directive)

Directive 73/23/EEC "Electrical Equipment Designed For Use Within Certain Voltage Limits" (Low Voltage Directive)

The EU declaration of conformity is available for the responsible authorities according to the above-mentioned EU directive at the following address:

Industrial Ethernet OSM/ESM	84
C79000-Z8976-C068-10

Image 88

Contents Simatic NET Classification of Safety-Related Notices Copyright Siemens AG 2000/02, All rights reservedSafety Instructions Regarding your Product TrademarksQualified Personnel Correct Usage of Hardware ProductsCorrect Usage of Software Products Prior to StartupInstalling an OSM/ESM PrefacePurpose of the Operating Instructions PackageFurther Documentation Validity of the Operating InstructionsFinding Information Guide to the Manual AudiencePersonnel Qualification Requirements Standards and ApprovalsContents Introduction Introduction OSM ITP62 Overview of the Variants of the OSM/ESMPossible Attachments Properties of the OSM ITP62 OSM ITP62-LD OSM ITP62-LDProperties of the OSM ITP62-LD ITP62-LDOSM ITP53 OSM ITP53Properties of the OSM ITP53 ESM ITP80 ESM ITP80Properties of the ESM ITP80 OSM TP62 OSM TP62Properties of the OSM TP62 ESM TP80 ESM TP80Properties of the ESM TP80 OSM BC08 OSM BC08Properties of the OSM BC08 OSM TP22 OSM TP22Properties of the OSM TP22 ESM TP40 ESM TP40Properties of the ESM TP40 Simple Network Configuration and Network Expansion Limitation of Errors to the Network Segment AffectedFunctions Increased Network PerformanceDeleting Addresses Setting the Transmission Rate, AutonegotiationPackets with the Vlan Priority Tag Functions Network Topologies with OSM/ESM Bus Structure Bus with OSMBus with ESMs Redundant Ring Structure Redundant Ring Structure with OSMsESM in RM mode Redundant Coupling of Network Segments OSM/ESM Simultaneous Standby and Redundancy Manager Operation Port Assignment in the Standby ModeReplacing the Standby Master During Operation OSM RM mode Compatibility of OSM Version 2/ESM with OSM/ORM Version CompatibilityRing with OSM Version 2 as Redundancy Manager Redundant Coupling of Rings Standby Master Slave OSM Coupling Network Segments RM mode OSMInterfaces, Displays and Operator Controls ITP Ports ITP/TP PortsTP Ports Autonegotiation Mode Properties of the TP/ITP PortsLink Control Auto Polarity ExchangeInterfaces, Displays and Operator Controls FO Ports Standby-Sync Port Serial Interface PinoutTerminal Block for the Power Supply and Signaling Contact Signaling Contact Power SupplyRM Mode additional OSM/ESM in the Standby Mode Digital Inputs Input voltage must not exceed +30V DC or fall below -30V DCFault red LED Displays and Operator ControlsLED Display Status Stby Standby green LEDRM Redundancy Manager green LED LED Power Display mode MeaningFault Mask Port LEDs DisplayFull duplex Port LED Two-Pin DIP Switch DIP SwitchesSelect/Set Button Installation, Commissioning, Cleaning Maintenance Do not install damaged components Unpacking, Checking the ConsignmentInstallation PreparationsInstalling the OSM on a DIN Standard Rail Standard Rail MountingRemoving from a Standard Rail Removing from the Standard RailInstallation on a Simatic S7-300 Rail Installation on the S7-300 RailInstallation in Pairs in the 19 Cubicle Installation in the 19 CubicleWall Mounting Wall MountingWall Mounting Cleaning Maintenance Firmware Update Specifying the keyword OSM FirmwareFirmware Update Firmware Update Firmware Update Firmware Update Technical Specifications PortsTechnical Specifications Permitted Cable Lengths Switching Properties of OSM/ESMCascading Depth Only horizontal installation Permitted Ambient Conditions/EMCMechanical Design PermittedConsignment / Order Numbers Accessories Product name Standards and ApprovalsCE Mark Area of Application Approval for AustraliaUL Approval CSA CertificationFM Approval Adherence to Installation Instructions Fault Mask Filtering ITP Port GlossaryLink Control LatencyTP Port Industrial Ethernet OSM/ESM C79000-Z8976-C068-10 References Http//www4.ad.siemens.de/view/cs/de/8677203Industrial Ethernet OSM/ESM C79000-Z8976-C068-10 Index Ambient conditions, permittedIndex