Siemens ESM, OSM Installation in Pairs in the 19 Cubicle, Installation in the 19 Cubicle

Page 72

Installation, Commissioning, Cleaning and Maintenance

Installation in Pairs in the 19" Cubicle

To install in pairs in the 19" cubicle, you require the two securing brackets supplied.

1.First screw the two OSMs/ESMs together using the supplied holding plate on the rear.

2.Fit two of the supplied brackets to the sides

3.Secure the two devices using the brackets in the 19" cubicle. Please note that the OSM/ESM must be grounded with a low resistance via the two holding brackets.

Interconnecting the devices at the rear

Figure 30: Installation in the 19" Cubicle

68	Industrial Ethernet OSM/ESM
	C79000-Z8976-C068-10

Image 72

Contents Simatic NET Classification of Safety-Related Notices Copyright Siemens AG 2000/02, All rights reservedSafety Instructions Regarding your Product TrademarksQualified Personnel Correct Usage of Hardware ProductsCorrect Usage of Software Products Prior to StartupInstalling an OSM/ESM PrefacePurpose of the Operating Instructions PackageValidity of the Operating Instructions Further DocumentationFinding Information Guide to the Manual AudiencePersonnel Qualification Requirements Standards and ApprovalsContents Introduction Introduction Overview of the Variants of the OSM/ESM OSM ITP62Possible Attachments Properties of the OSM ITP62 OSM ITP62-LD OSM ITP62-LDProperties of the OSM ITP62-LD ITP62-LDOSM ITP53 OSM ITP53Properties of the OSM ITP53 ESM ITP80 ESM ITP80Properties of the ESM ITP80 OSM TP62 OSM TP62Properties of the OSM TP62 ESM TP80 ESM TP80Properties of the ESM TP80 OSM BC08 OSM BC08Properties of the OSM BC08 OSM TP22 OSM TP22Properties of the OSM TP22 ESM TP40 ESM TP40Properties of the ESM TP40 Simple Network Configuration and Network Expansion Limitation of Errors to the Network Segment AffectedFunctions Increased Network PerformanceSetting the Transmission Rate, Autonegotiation Deleting AddressesPackets with the Vlan Priority Tag Functions Network Topologies with OSM/ESM Bus Structure Bus with OSMBus with ESMs Redundant Ring Structure Redundant Ring Structure with OSMsESM in RM mode Redundant Coupling of Network Segments OSM/ESM Port Assignment in the Standby Mode Simultaneous Standby and Redundancy Manager OperationReplacing the Standby Master During Operation OSM RM mode Compatibility of OSM Version 2/ESM with OSM/ORM Version CompatibilityRing with OSM Version 2 as Redundancy Manager Redundant Coupling of Rings Standby Master Slave OSM Coupling Network Segments RM mode OSMInterfaces, Displays and Operator Controls ITP/TP Ports ITP PortsTP Ports Autonegotiation Mode Properties of the TP/ITP PortsLink Control Auto Polarity ExchangeInterfaces, Displays and Operator Controls FO Ports Standby-Sync Port Serial Interface PinoutTerminal Block for the Power Supply and Signaling Contact Power Supply Signaling ContactRM Mode additional OSM/ESM in the Standby Mode Digital Inputs Input voltage must not exceed +30V DC or fall below -30V DCFault red LED Displays and Operator ControlsLED Display Status Stby Standby green LEDRM Redundancy Manager green LED LED Power Display mode MeaningFault Mask Port LEDs DisplayFull duplex Port LED Two-Pin DIP Switch DIP SwitchesSelect/Set Button Installation, Commissioning, Cleaning Maintenance Do not install damaged components Unpacking, Checking the ConsignmentInstallation PreparationsInstalling the OSM on a DIN Standard Rail Standard Rail MountingRemoving from a Standard Rail Removing from the Standard RailInstallation on a Simatic S7-300 Rail Installation on the S7-300 RailInstallation in Pairs in the 19 Cubicle Installation in the 19 CubicleWall Mounting Wall MountingWall Mounting Cleaning Maintenance Firmware Update Specifying the keyword OSM FirmwareFirmware Update Firmware Update Firmware Update Firmware Update Technical Specifications PortsTechnical Specifications Switching Properties of OSM/ESM Permitted Cable LengthsCascading Depth Only horizontal installation Permitted Ambient Conditions/EMCMechanical Design PermittedConsignment / Order Numbers Accessories Standards and Approvals Product nameCE Mark Area of Application Approval for AustraliaUL Approval CSA CertificationFM Approval Adherence to Installation Instructions Fault Mask Filtering ITP Port GlossaryLatency Link ControlTP Port Industrial Ethernet OSM/ESM C79000-Z8976-C068-10 References Http//www4.ad.siemens.de/view/cs/de/8677203Industrial Ethernet OSM/ESM C79000-Z8976-C068-10 Index Ambient conditions, permittedIndex