Allied Telesis AT-CV5000 manual Power Supplies, Rear EXP. Slot

Page 31

AT-CV5000 Media Converter Chassis Installation Guide

Power Supplies

The AT-CV5000 chassis is shipped with two rear slots designated for the power supplies. Two power supply options are available:

ˆAT-PWR14 AC module

ˆAT-PWR15 DC module

Caution

The AT-CV5000 Media Converter chassis can contain two power supplies of the same type (AC or DC) or a combination of the two versions with the same power ratings. Make sure not to mix power supplies with different power ratings in the same chassis.

For information on the power supply module, refer to the documentation that is shipped with the module.

An AC powered chassis is shown in Figure 8 and a DC-powered chassis is shown in Figure 9.

A

CVFAN-AT

A

CVFAN-AT

 

 

REAR EXP. SLOT

 

 

A

B

 

100-240VAC~

WARNING

WARNING

100-240VAC~

This unit might have more than one power input. To

This unit might have more than one power input. To

reduce the risk of electric shock, disconnect all power

reduce the risk of electric shock, disconnect all power

 

inputs before servicing unit.

inputs before servicing unit.

 

AT-PWR14

AT-PWR14

POWER

POWER

FAULT

FAULT

Figure 8. AT-CV5000 AC Powered Chassis

 

 

 

REAR EXP. SLOT

 

 

 

A

 

 

B

 

 

WARNING

FOR CENTRALIZED DC POWER

WARNING

FOR CENTRALIZED DC POWER

 

40-60VDC

This unit might have more than one power input. To

CONNECTION, INSTALL ONLY IN

This unit might have more than one power input. To

CONNECTION, INSTALL ONLY IN

40-60VDC

reduce the risk of electric shock, disconnect all power

A RESTRICTED AREA.

reduce the risk of electric shock, disconnect all power

A RESTRICTED AREA.

AT-PWR15

AT-PWR15

POWER

POWER

FAULT

FAULT

Figure 9. AT-CV5000 DC Powered Chassis

B

AT-CVFAN

1163

B

AT-CVFAN

1162

When two power supplies are installed, one provides full power to the chassis and the one of them works in standby mode. If one power supply fails, the remaining power supply provides all the power to the system, preventing a system failure.

31

Image 31
Contents Installation Guide Page Electrical Safety and Emissions Standards Translated Safety Statements Contents Physical Specifications AT-CV5000 Media Converter Chassis Installation Guide Contents Figures Figures Tightening the Captive Screw Tables Tables Preface Symbol Meaning Description Safety Symbols Used in this DocumentWhere to Find Web-based Guides Contacting Allied Telesis Management Software UpdatesChapter OverviewAT-CV5000 AT-CV5000 OverviewSystem Description Hardware Features Software FeaturesFront and Rear Panel Components Reset ButtonLED Interface Card Interface Card LEDs Reset LINE/ EXP Button AT-CV5M01 Management Card 10/100Base-TX Twisted Pair Port Button LEDs CPU ResetGreen Twisted pair port is operating in full Duplex mode Link Test MissingLink Converteon Line CardsLine Card Port Descriptions Smart MissingLinkIllustrates the AT-CV5PNLx Series blank slot covers Blank Slot CoversRear EXP. Slot Power Supplies201 Fan ModulesManagement Connections Few Basics about Media Converters MAC Address Table Duplex ModePass-through Standalone Topology Network TopologiesBack-to-Back Network Topology Overview Installation Reviewing Safety Precautions AT-CV5000 Media Converter Chassis Installation Guide Installation AT-CV5000 Media Converter Chassis Installation Guide Selecting a Site for the Chassis Unpacking the Chassis Inserting the Retaining Clip into the Retaining Bracket Retaining Clip Properly Installed in the Bracket 236 Installing the AT-CV5000 Chassis in a RackAT-CV5000 Media Converter Chassis Installation Guide Grounding the AT-CV5000 Chassis Frame Ground ConnectorsFrame ground stud for power supply a is shown in Figure Installing a Converteon Line Card Inserting a Line Card 249 Cabling a Fiber Optic Port Cabling a Converteon Line Card in an AT-CV5000 ChassisFiber Connector Cabling a Simplex SC Connector Cabling an SFP Transceiver Connecting Fiber Optic Cables to the SFP Transceiver VAC ~ Powering On an AC Powered ChassisPWR a PWR B PWR a AT-CV5000 Media Converter Chassis Installation Guide DC Terminal Block Powering On a DC Powered Chassis8mm ±1mm 31in. ±0.039in 256 Starting a Local Management Session Connecting a Management Cable to the RS-232 Console PortAT-S70 Main Menu AT-CV5000 Media Converter Chassis Installation Guide Guide Starting a Remote Management Sessionˆ Usernames and passwords are case-sensitive Installation Working with Line Cards and other Modules Removing a Converteon Line Card AT-CV5000 Media Converter Chassis Installation Guide Working with the AT-CV5M01 Management Card Installing anManagement Card Resetting an Replacing an Installing an AT-CM70S Line Card 907 Resetting Converteon Line Cards/Rear Expansion Module Installing an AT-PWR14 AC Power Supply AT-PWR14 Installing an AT-PWR15 DC Power Supply AT-PWR15 Replacing an AT-CVFAN Module Removing an AT-CVFAN Module from Fan Slot a Tightening the Screws on the AT-CVFAN Module in Slot a AT-CV5PWRAC Blank Slot Cover Installing a Blank Slot CoverAT-CM202 AT-CV5PNL2 AT-CV5PNL3 AT-PWR14 Troubleshooting Troubleshooting RDY LED is Blinking RDY LED is OFF FLT LED is PWR LED isLK LED is Blinking LK LED is OFF FLT LED is Steadily on LK LED is OFFAT-CV5000 Media Converter Chassis Installation Guide Troubleshooting 100 Appendix a Physical SpecificationsEnvironmental Specifications Power SpecificationsStandards Safety and Electromagnetic Emissions CertificationsRJ-45 Twisted Pair Port Pinouts Pin SignalIllustrates the pin layout to an RS-232 terminal port RS-232 Terminal Port PinoutsPin Mini-DIN Console Port Pinouts Dual SC Connector Simplex SC Connector SC Type ConnectorsDual ST Connector Cable Dual ST Type Connector CableSFP Transceiver Cable SFP Transceiver CableAppendix B Cleaning Fiber Optic ConnectorsUsing a Cartridge-Type Cleaner 111 Cleaning a Recessed Ferrule If desired, repeat step Using a Swab113 Appendix B Cleaning Fiber Optic Connectors 114