Allied Telesis manual AT-CV5000 Media Converter Chassis Installation Guide

Page 99

AT-CV5000 Media Converter Chassis Installation Guide

ˆVerify that the end node connected to the port is ON and is operating properly.

ˆCheck that the fiber optic cable is securely connected to the fiber optic port on the media converter and on the end node.

ˆCheck to be sure that the end node connected to the port is operating at the same port speed.

ˆVerify the fiber connections are correct that is the converter’s TX port is connected to the end node’s RX port, and the converter’s RX port is connected to the end node’s TX port.

ˆCheck to be sure that the end nodes connected to the switch are operating at the same duplex mode.

ˆTest the attenuation on the fiber cable to ensure that it does not exceed acceptable values.

ˆVerify that you are using the appropriate type of fiber optic cables and that you have not exceeded the maximum operating distances.

ˆCheck that the operating specifications of the fiber optic port on the end node are compatible with the operating specifications of the fiber optic port on the converter.

If you are still experiencing problems after testing and troubleshooting the installation, contact Allied Telesis Technical Support for assistance. Refer to “Contacting Allied Telesis” on page 16 or visit our web site at www.alliedtelesis.com for support information.

99

Image 99
Contents Installation Guide Page Electrical Safety and Emissions Standards Translated Safety Statements Contents Physical Specifications AT-CV5000 Media Converter Chassis Installation Guide Contents Figures Figures Tightening the Captive Screw Tables Tables Preface Symbol Meaning Description Safety Symbols Used in this DocumentWhere to Find Web-based Guides Contacting Allied Telesis Management Software UpdatesChapter OverviewAT-CV5000 AT-CV5000 OverviewSystem Description Hardware Features Software FeaturesFront and Rear Panel Components Reset ButtonLED Interface Card Interface Card LEDs Reset LINE/ EXP Button AT-CV5M01 Management Card 10/100Base-TX Twisted Pair Port Button LEDs CPU ResetGreen Twisted pair port is operating in full Duplex mode Link Test MissingLink Converteon Line CardsLine Card Port Descriptions Smart MissingLinkIllustrates the AT-CV5PNLx Series blank slot covers Blank Slot CoversRear EXP. Slot Power Supplies201 Fan ModulesManagement Connections Few Basics about Media Converters MAC Address Table Duplex ModePass-through Standalone Topology Network TopologiesBack-to-Back Network Topology Overview Installation Reviewing Safety Precautions AT-CV5000 Media Converter Chassis Installation Guide Installation AT-CV5000 Media Converter Chassis Installation Guide Selecting a Site for the Chassis Unpacking the Chassis Inserting the Retaining Clip into the Retaining Bracket Retaining Clip Properly Installed in the Bracket 236 Installing the AT-CV5000 Chassis in a RackAT-CV5000 Media Converter Chassis Installation Guide Grounding the AT-CV5000 Chassis Frame Ground ConnectorsFrame ground stud for power supply a is shown in Figure Installing a Converteon Line Card Inserting a Line Card 249 Cabling a Fiber Optic Port Cabling a Converteon Line Card in an AT-CV5000 ChassisFiber Connector Cabling a Simplex SC Connector Cabling an SFP Transceiver Connecting Fiber Optic Cables to the SFP Transceiver VAC ~ Powering On an AC Powered ChassisPWR a PWR B PWR a AT-CV5000 Media Converter Chassis Installation Guide DC Terminal Block Powering On a DC Powered Chassis8mm ±1mm 31in. ±0.039in 256 Starting a Local Management Session Connecting a Management Cable to the RS-232 Console PortAT-S70 Main Menu AT-CV5000 Media Converter Chassis Installation Guide Guide Starting a Remote Management Sessionˆ Usernames and passwords are case-sensitive Installation Working with Line Cards and other Modules Removing a Converteon Line Card AT-CV5000 Media Converter Chassis Installation Guide Installing an Working with the AT-CV5M01 Management CardManagement Card Resetting an Replacing an Installing an AT-CM70S Line Card 907 Resetting Converteon Line Cards/Rear Expansion Module Installing an AT-PWR14 AC Power Supply AT-PWR14 Installing an AT-PWR15 DC Power Supply AT-PWR15 Replacing an AT-CVFAN Module Removing an AT-CVFAN Module from Fan Slot a Tightening the Screws on the AT-CVFAN Module in Slot a AT-CV5PWRAC Blank Slot Cover Installing a Blank Slot CoverAT-CM202 AT-CV5PNL2 AT-CV5PNL3 AT-PWR14 Troubleshooting Troubleshooting RDY LED is Blinking RDY LED is OFF FLT LED is PWR LED isLK LED is Blinking LK LED is OFF FLT LED is Steadily on LK LED is OFFAT-CV5000 Media Converter Chassis Installation Guide Troubleshooting 100 Appendix a Physical SpecificationsEnvironmental Specifications Power SpecificationsStandards Safety and Electromagnetic Emissions CertificationsRJ-45 Twisted Pair Port Pinouts Pin SignalIllustrates the pin layout to an RS-232 terminal port RS-232 Terminal Port PinoutsPin Mini-DIN Console Port Pinouts Dual SC Connector Simplex SC Connector SC Type ConnectorsDual ST Connector Cable Dual ST Type Connector CableSFP Transceiver Cable SFP Transceiver CableAppendix B Cleaning Fiber Optic ConnectorsUsing a Cartridge-Type Cleaner 111 Cleaning a Recessed Ferrule If desired, repeat step Using a Swab113 Appendix B Cleaning Fiber Optic Connectors 114