Allied Telesis AT-CV5000 manual AT-CV5PNL2

Page 92

Chapter 3: Working with Line Cards and other Modules

Installing an

AT-CV5PNL2

Blank Slot Cover

The AT-CV5PNL2 blank slot cover is designed to cover any unoccupied power supply module slots in the AT-CV5000 chassis model only.

To install an AT-CV5PNL2 blank slot cover, perform the following procedure:

1.Remove the AT-CV5PNL2 blank slot cover from its shipping package and store the package in a safe place.

Note

You must use the original package if you need to return the unit to Allied Telesis.

2.Select the power supply slot in the AT-CV5000 chassis where you want to install the blank slot cover.

3.Align the back edge of the blank slot cover with the alignment guides located inside the slot.

4.Slide the blank slot cover into the slot, as shown in Figure 68, until the slot cover is flush with the front of the chassis.

WARNINGThis unit
reduce thme rigishkt ohfaveelemctorircesthhan one po
ock, discownneercint paulltp. Toower	100-240	VAC~
		VAC~

226

Figure 68. Inserting an AT-CV5PNL2 Blank Slot Cover

5.Use a Phillips screwdriver to tighten the captive screws, as shown in Figure 69.

WARNINGThis unit
reduce thme ight have
risk of elemore than
ctric shocko, ndeispcower input.	To
onnect all	To	100-
	power	100-
		240VAC~

273

Figure 69. Tightening the Captive Screws on an AT-CV5PNL2

92

Image 92

Contents Installation Guide Page Electrical Safety and Emissions Standards Translated Safety Statements Contents Physical Specifications AT-CV5000 Media Converter Chassis Installation Guide Contents Figures Figures Tightening the Captive Screw Tables Tables Preface Safety Symbols Used in this Document Symbol Meaning DescriptionWhere to Find Web-based Guides Management Software Updates Contacting Allied TelesisOverview ChapterAT-CV5000 Overview AT-CV5000Hardware Features Software Features System DescriptionReset Button Front and Rear Panel ComponentsLED Interface Card Interface Card LEDs Reset LINE/ EXP Button AT-CV5M01 Management Card 10/100Base-TX Twisted Pair Port CPU Reset Button LEDsGreen Twisted pair port is operating in full Duplex mode Converteon Line Cards Link Test MissingLinkSmart MissingLink Line Card Port DescriptionsBlank Slot Covers Illustrates the AT-CV5PNLx Series blank slot coversPower Supplies Rear EXP. SlotFan Modules 201Management Connections MAC Address Table Duplex Mode Few Basics about Media ConvertersPass-through Network Topologies Standalone TopologyBack-to-Back Network Topology Overview Installation Reviewing Safety Precautions AT-CV5000 Media Converter Chassis Installation Guide Installation AT-CV5000 Media Converter Chassis Installation Guide Selecting a Site for the Chassis Unpacking the Chassis Inserting the Retaining Clip into the Retaining Bracket Retaining Clip Properly Installed in the Bracket Installing the AT-CV5000 Chassis in a Rack 236AT-CV5000 Media Converter Chassis Installation Guide Frame Ground Connectors Grounding the AT-CV5000 ChassisFrame ground stud for power supply a is shown in Figure Installing a Converteon Line Card Inserting a Line Card 249 Cabling a Converteon Line Card in an AT-CV5000 Chassis Cabling a Fiber Optic PortFiber Connector Cabling a Simplex SC Connector Cabling an SFP Transceiver Connecting Fiber Optic Cables to the SFP Transceiver Powering On an AC Powered Chassis VAC ~PWR a PWR B PWR a AT-CV5000 Media Converter Chassis Installation Guide Powering On a DC Powered Chassis DC Terminal Block8mm ±1mm 31in. ±0.039in 256 Connecting a Management Cable to the RS-232 Console Port Starting a Local Management SessionAT-S70 Main Menu AT-CV5000 Media Converter Chassis Installation Guide Starting a Remote Management Session Guideˆ Usernames and passwords are case-sensitive Installation Working with Line Cards and other Modules Removing a Converteon Line Card AT-CV5000 Media Converter Chassis Installation Guide Management Card Installing anWorking with the AT-CV5M01 Management Card Resetting an Replacing an Installing an AT-CM70S Line Card 907 Resetting Converteon Line Cards/Rear Expansion Module Installing an AT-PWR14 AC Power Supply AT-PWR14 Installing an AT-PWR15 DC Power Supply AT-PWR15 Replacing an AT-CVFAN Module Removing an AT-CVFAN Module from Fan Slot a Tightening the Screws on the AT-CVFAN Module in Slot a AT-CV5PWRAC Installing a Blank Slot Cover Blank Slot CoverAT-CM202 AT-CV5PNL2 AT-CV5PNL3 AT-PWR14 Troubleshooting Troubleshooting PWR LED is RDY LED is Blinking RDY LED is OFF FLT LED isFLT LED is Steadily on LK LED is OFF LK LED is Blinking LK LED is OFFAT-CV5000 Media Converter Chassis Installation Guide Troubleshooting 100 Physical Specifications Environmental SpecificationsPower Specifications Appendix aSafety and Electromagnetic Emissions Certifications StandardsPin Signal RJ-45 Twisted Pair Port PinoutsRS-232 Terminal Port Pinouts Illustrates the pin layout to an RS-232 terminal portPin Mini-DIN Console Port Pinouts SC Type Connectors Dual SC Connector Simplex SC ConnectorDual ST Type Connector Cable Dual ST Connector CableSFP Transceiver Cable SFP Transceiver CableCleaning Fiber Optic Connectors Appendix BUsing a Cartridge-Type Cleaner 111 Using a Swab Cleaning a Recessed Ferrule If desired, repeat step113 Appendix B Cleaning Fiber Optic Connectors 114