Allied Telesis AT-MC601 manual Powering On the Provider Unit

Page 33

Installation

3.Next, connect a telephone line cable from the VDSL Line port to the wall/interior telephone line, as shown in Figure 22, so that the Provider unit can communicate with the Subscriber unit.

Powering On the Provider Unit

10100BBaasseeTTX/ LINK

ACT

PWR

LINE

AT-

 

 

 

 

ERR

MC601

VDSL

EXTENDED

MGMT

 

 

ETHERNET

PSTN

LINK

 

 

 

 

 

 

 

 

MCR1

2

AT-MC602VDSL EXTENDED ETHERNET

 

Wall/Interior Phone Line

Figure 22 VDSL Line to Wall/Interior Phone Line

Note

The procedure for connecting the management cable is described in ”Cabling Preparations” on page 36.

Powering on the AT-MC602 Provider Unit requires that the host equipment, AT-MCR12 rackmount chassis, is powered on as well.

Warning

The QUALIFIED SERVICE PERSONNEL must verify that the AT-MCR12 power cord is connected to the socket provided with the ground conductor.

If the power cord is not connected, the QUALIFIED SERVICE PERSONNEL must install a permanent ground connection using the bond stud on the rear panel of the AT-MCR12 chassis.

For detailed information on how to power on the AT-MCR12 unit, refer to the AT-MCR12 Media Converter Rackmount Chassis Installation Manual.

33

Image 33
Contents Installation and User’s Guide Page Electrical Safety and Emission Statement Contents Appendix a How This Guide is Organized PrefaceDocument Conventions Contacting Allied Telesyn Technical Support Product Description Summary of FeaturesEthernet Port AT-MC601 Subscriber Unit AT-MC602 Provider OverviewAT-MC601 Location of ComponentsPin Assignment Hardware FeaturesPstn Port 10/100 Mbps Twisted Pair Ethernet Port TX+ RX+ Pin MDI Signal MDI-X SignalColor Description Management Cable10/100Base-TX Port Line PortRS-232 Pin DIN Pin Signal DC Power Supply Input Port External AC/DC Power AdapterSoftware Features Installation Installation Safety Precautions Additional Compliance Statements Selecting a Site for the Network Extender Cables Not Included Cables Port ConnectorUnpacking the Network Extender Installing the AT-MC601 Subscriber Unit Using Subscriber Unit On a DesktopWall-Mounting Subscriber Unit Positioning The Switch Onto The Wall Screws Pstn to Telephone MCR Powering On the Subscriber UnitUsing the Provider Unit on a Desktop Installing the AT-MC602 Provider UnitWall-Mounting Provider Unit Grounding the Provider Unit Rack Mount Set in Rack Rack-Mounting Provider UnitProvider Unit Internet Service ProviderPowering On the Provider Unit Warranty Registration Configuration Downloading Software Updates Cabling Preparations Starting a Configuration SessionOpening Configuration Software Configuration Configuring the Provider UnitActual Mbps Upstream/DownstreamMin Mbps Max MbpsAbout ApplyCorrected RS errors /s SNR of Received SignalMean Square Error Full Constellation LinkReduced Constellation Link Signal DetectedTC Synchronized Ethernet Encapsulation SyncTxRx Counters Error CountersCollision Counters ClearStop/Start Configuring the Subscriber Unit InstallNormal AT-MC601, AT-MC602 Installation and User’s Guide Troubleshooting Communication Error Message Cant read link status AT-MC601, AT-MC602 Installation and User’s Guide Default Configuration Settings Physical Specifications Technical SpecificationsSafety and Electromagnetic Compatibility Certifications Translated Electrical Safety and Emission Information Lightning Danger Temperature of 40 degrees CUmgebungstemperatur von nicht mehr als 40 C entworfen Gefahr Durch BlitzschlagFare Under Uvejr Lovgivning for elektriske installationerMaksimum 40 grader C 10Veiligheid Gevaar Voor BlikseminslagBedragen dan 40 graden Celsius Ambiante maximum de 40 degrés Celsius 40 C SalamaniskuvaaraAmbientale massima di 40 gradi centigradi Pericolo Di FulminiSikkerhet Fare For LynnedslagPå 40 grader celsius Ambiente máxima de 40 graus centígrados Perigo De Choque Causado Por RaioTemperatura ambiental máxima de 40 grados C Peligro De RayosGrader Celsius Fara För Blixtnedslag