Allied Telesis AT-MC601 manual Selecting a Site for the Network Extender

Page 21

Installation

Selecting a Site for the Network Extender

Observe the following requirements when choosing a site for your network extender:

If you plan to install the AT-MCR12 in an equipment rack, check to be sure that the rack is safely secured and that it will not tip over. Devices in a rack should be installed starting at the bottom, with the heavier devices near the bottom of the rack.

If you are installing the network extender on a table, be sure that the table is level and secure.

The power outlet for the network extender should be located near the unit and should be easily accessible.

The site should provide for easy access to the ports on the front of the network extender. This will make it easy for you to connect and disconnect cables, as well as view the LEDs.

To allow proper cooling of the network extender, air flow around the unit and through its vents on the side should not be restricted.

Do not place objects on top of the network extender.

Do not expose the network extender to moisture or water.

Make sure that the site is a dust-free environment.

You should use dedicated power circuits or power conditioners to supply reliable electrical power to the network extenders.

21

Image 21
Contents Installation and User’s Guide Page Electrical Safety and Emission Statement Contents Appendix a How This Guide is Organized PrefaceDocument Conventions Contacting Allied Telesyn Technical Support Product Description Summary of FeaturesEthernet Port AT-MC601 Subscriber Unit AT-MC602 Provider OverviewAT-MC601 Location of ComponentsPin Assignment Hardware FeaturesPstn Port 10/100 Mbps Twisted Pair Ethernet Port TX+ RX+ Pin MDI Signal MDI-X SignalColor Description Management Cable10/100Base-TX Port Line PortRS-232 Pin DIN Pin Signal DC Power Supply Input Port External AC/DC Power AdapterSoftware Features Installation Installation Safety Precautions Additional Compliance Statements Selecting a Site for the Network Extender Cables Not Included Cables Port ConnectorUnpacking the Network Extender Installing the AT-MC601 Subscriber Unit Using Subscriber Unit On a DesktopWall-Mounting Subscriber Unit Positioning The Switch Onto The Wall Screws Pstn to Telephone MCR Powering On the Subscriber UnitUsing the Provider Unit on a Desktop Installing the AT-MC602 Provider UnitWall-Mounting Provider Unit Grounding the Provider Unit Rack Mount Set in Rack Rack-Mounting Provider UnitProvider Unit Internet Service ProviderPowering On the Provider Unit Warranty Registration Configuration Downloading Software Updates Cabling Preparations Starting a Configuration SessionOpening Configuration Software Configuration Configuring the Provider UnitActual Mbps Upstream/DownstreamMin Mbps Max MbpsAbout ApplyCorrected RS errors /s SNR of Received SignalMean Square Error Full Constellation LinkReduced Constellation Link Signal DetectedTC Synchronized Ethernet Encapsulation SyncTxRx Counters Error CountersCollision Counters ClearStop/Start Configuring the Subscriber Unit InstallNormal AT-MC601, AT-MC602 Installation and User’s Guide Troubleshooting Communication Error Message Cant read link status AT-MC601, AT-MC602 Installation and User’s Guide Default Configuration Settings Physical Specifications Technical SpecificationsSafety and Electromagnetic Compatibility Certifications Translated Electrical Safety and Emission Information Lightning Danger Temperature of 40 degrees CUmgebungstemperatur von nicht mehr als 40 C entworfen Gefahr Durch BlitzschlagFare Under Uvejr Lovgivning for elektriske installationerMaksimum 40 grader C 10Veiligheid Gevaar Voor BlikseminslagBedragen dan 40 graden Celsius Ambiante maximum de 40 degrés Celsius 40 C SalamaniskuvaaraAmbientale massima di 40 gradi centigradi Pericolo Di FulminiSikkerhet Fare For LynnedslagPå 40 grader celsius Ambiente máxima de 40 graus centígrados Perigo De Choque Causado Por RaioTemperatura ambiental máxima de 40 grados C Peligro De RayosGrader Celsius Fara För Blixtnedslag