AC International MTA128ST-USB manual Result Codes

Page 71

Chapter 4 - AT Commands, S-Registers, and Result Codes

Result Codes

When the MTA128ST-USB (TA) receives an AT command from the computer or terminal, it attempts to execute the command, then sends a status message to the computer or terminal that reports the result of the command. The TA provides you with several of these response messages, or result codes, which can be displayed on your monitor or intercepted and used by your communications software. Using the V command, you can select whether the result codes are terse (numbers) or verbose (words).

The TA’s result codes are listed below. Note that the speed of an ISDN channel is always either 56 Kbps or 64 Kbps. Connect messages indicate the speed of the connection between the TA and your computer or terminal.

TERSE

VERBOSE

DEFINITION

0

OK

TA executed the command without error

1

Connect

TA established an ISDN connection

2

Ring

TA detected a ring caused by incoming call

3

No carrier

TA did not detect carrier within time allotted by S-

 

 

Register S7

4

Error

Error in the AT command

5

Connect 1200

TA connected at 1200 bps

6

No dial tone

TA has a poor connection to ISDN network

7

Busy

TA detected a busy signal

9

Connect 600

TA connected at 600 bps

10

Connect 2400

TA connected at 2400 bps

11

Connect 4800

TA connected at 4800 bps

12

Connect 9600

TA connected at 9600 bps

14

Connect 19200

TA connected at 19200 bps

28

Connect 38400

TA connected at 38400 bps

56

Connect 56000

TA connected at 56000 bps

64

Connect 64000

TA connected at 64000 bps

P

/PPP

TA using Point-to-Point protocol

T

/V.110

TA using V.110 rate adaption protocol*

V

/V.120

TA using V.120 rate adaption protocol

X

/X75

TA using X.75 rate adaption protocol

*The MTA128ST-USB is manufactured in two builds. To determine the build of your terminal adapter (TA), issue the ATI2 command in a terminal window. If the TA responds to the command with MTA128ST- USB, then it supports V.110. If your TA resonds to the ATI2 command with MTA128ST-USB-RC, V.110 support is not available.

71

Image 71
Contents User Guide User Guide Contents Troubleshooting Introduction and Description MultiModemISDN User Guide IntroductionProduct Description Universal Serial Bus USBIntroduction and Description Manual OrganizationFeatures LED Indicators Technical SpecificationsHardware Installation Unpacking Your MTA128ST-USB Safety Warning Telecom/ISDN-STHardware Installation MultiModem Isdn User Guide Connecting the MTA128ST-USB to Your SystemAssembling the MTA128ST-USB Connecting to Analog Equipment Connecting to Your ComputerConnecting to Power Connecting to Your Isdn Network TerminatorLED Indicators References Hardware Installation Data ProtocolSoftware Installation and Configuration Install Hardware Device Drivers dialog box displays Installing in WindowsSoftware Installation and Configuration If the Digital Signature Not Found dialog box displays Page MTA128ST-USB CDC ML-PPP Properties dialog box displays Upgrade Device Driver Wizard dialog box displaysChanging the Modem Descriptor Windows Start Device Driver Installation dialog box displays Installing in Windows Software Installation and Configuration MultiModemISDN User Guide MTA128ST-USB ML-PPP Properties dialog box displays Update Device Driver Wizard dialog box displaysUpgrade Device Driver Wizard dialog box displays Software Installation and Configuration Removing Your Old Device from Windows 2000 and Windows 98 Click Start Settings Control PanelNetwork Configuration ConfigurationAT commands AT!N1= and AT*!N1= Call Control ConfigurationAT commands AT!C6= and AT*!C6= Dialing Stored Numbers To Install in Windows 2000/98/95 Isdn MTA128ST-USB Configuration UtilityWindows 2000 Dial-Up Networking MultiModemISDN User Guide If you select Accept incoming connections MultiModemISDN User Guide Windows 98/95 Dial-Up Networking MultiModemISDN User Guide Using AT Commands to Configure the MTA128ST-USB AT CommandsAT Commands, S-Registers and Result Codes AT Commands, S-Registers, and Result Codes Entering AT CommandsCommand Implementation AT Commands by FunctionData Call Commands C0=2 Net3 A97=nA97=0 A97=1DN=1 D3=0-63D3=240 D3=241D98 EN=nEN=1 EN=2RXG10 N2=nRXGn L5 and L6 =12Connect String normally it is issued by itself ATZ #X0 E4, &E6, &E13E12 E13MultiModemISDN User Guide $Dn ROMData Call Commands Command DSn Register Summary RegistersAT Commands, S-Registers, and Result Codes MultiModemISDN User Guide S34 S30S31 S50 S44S45 S49S51 RingS18 S53S54 S17AT Commands, S-Registers, and Result Codes S59 S58S62 S60S61 S65 S63S64 S68 S67S73 S69S70 S71S77 S75S76 S80 Result Codes Dialing Using AT Commands to Operate the MTA128ST-USBMaking a Call Modes of OperationAnswering a Call Hanging Up Troubleshooting None of the LEDs light when the MTA128ST-USB is on MTA128ST-USB dials but cannot make a connection TroubleshootingYou can place data calls but not voice calls or vice versa MTA128ST-USB disconnects while online MultiModemISDN User Guide Warranty, Service, and Technical Support Addendum for International Products Limited WarrantyAddendum for North American Products Software User License Agreement Out of Warranty Repair Costs On-line Warranty RegistrationWarranty, Service and Tech Support MultiModem Isdn User Guide Contacting Technical Support ServiceTechnical Support Ordering Accessories Upgrading the MTA128ST-USB with FlashWizard Using FlashWizard to Upgrade FirmwareAppendixes Industry Canada EMC, Safety, and Terminal Directive ComplianceAppendix a Regulatory Compliance Class B Statement FCC PartMultiVOIP 200 User Guide Quick Setup ExampleProfile 1 &F1 V.110 Asynchronous Operation Profile 2 &F2 V.120 Asynchronous Operation Profile 4 &F4 ML-PPP Asynchronous Operation Glossary Glossary SymbolMultiModemISDN User Guide Glossary MultiModemISDN User Guide Glossary 100 TA- See terminal adapter 101102 103 Index 105 Index106 42, 52107 Isdn MTA128ST-USB Config utility108 Rings