Sennheiser HMEC 26-2 Cable -RP-2, Cable -DP-2, Cable -KP, -KP-2, -B-K-2, -B-KP-2, -BV-K-2, Hmec

Page 30

Cable -RP-2

Connector assignment

Cable -RP-2

	Solder side
	1	6	1	NoiseGardTM (DC+)
	1	6	2	Audio Lo / DC–
	2	5	3	Audio Hi left
	3	4	4	Audio Hi right
	3	4	5	Microphone Hi
			5	Microphone Hi
			6	Microphone Lo

Cable -DP-2

Solder side
			1	Audio Hi
4		3	2	Audio Lo
4		3	3	Microphone Hi
		2	3	Microphone Hi
5	6	1	4	Microphone Lo
		1	5	NoiseGardTM (DC+)
			6	DC–

Cable -KP, -KP-2, -B-K-2, -B-KP-2, -BV-K-2

¼" (6.3 mm) jack plug				PJ-068 equivalent
	1	2	3	1 2		3
Cable -KP / -KP-2 / -B-KP-2
1	Audio Hi			1	NoiseGard™ (DC+)
2	not assigned			2	Microphone Hi
3	Audio Lo / DC–			3	Microphone Lo
Cable -B-K-2
1	Audio Hi			1	not assigned
2	not assigned			2	Microphone Hi
3	Audio Lo			3	Microphone Lo

Cable -BV-K-2

1	Audio Hi left	1	not assigned
2	Audio Hi right	2	Microphone Hi
3	Audio Lo	3	Microphone Lo	HMEC 26-2 29
				HMEC 26-2 29

Image 30

Contents HMEC Important safety information Preventing health problems and accidentsPreventing damage to the product and dysfunctions Only clean the product with a soft, dry clothIntended use Intended use of the product includesThe HMEC 26-2 headset FeaturesPackage contents Flipping away one earcup OperationPutting on the headset OperationPositioning the microphone Turning the microphone boomAdjusting the volume directly on the audio system Adjusting the microphone sensitivityHearing damage due to high volumes Control unit 5 BOOM switch L /RThe control units of the HMEC 1 2 3 4 5 6Cable -CP Cable -CP-2 Cable -KP Cable -KP-2 Cable -NP Cable -RP-2 Cable -DP-210 HMEC Using the headset Switching NoiseGard on/offAdjusting the volume Switching between mono and stereo modeChanging the left and right stereo channel Powering NoiseGard via two rechargeable batteries Activating the “auto shut-off” functionMeaning Switching the TalkThrough function on/off HMEC 26-2-T only Set the switch to the position ASOConnecting a mobile telephone Danger of accident due to reduced attentionConnecting an additional audio player Attaching the belt clip Attaching the cable clip 18 HMECCare and maintenance Cleaning and maintaining the headsetReplacing the ear pads Attach the new headband paddings by joining the fastenings strips Replacing the headband paddingsPut the new headband paddings around the headbands 20 HMECAccessories and spare parts AccessoriesAudio cable, length 0.6 m 2 x 3.5 mm stereo jack plug Spare partsCable clip Audio cable, length 0.6 m, 2 x 2.5 mm jack plugProduct and cable variants Part Number ModelCat. No 24 HMECThese headsets can be combined with all cables see page 1 2 3 4 5 6 7 8 9 A B C D E F GHeadphones SpecificationsSpecifications 26 HMECMicrophone incl. preamplifier General dataNoiseGard professional Cable -CP, -CP-2, -B-CP-2 Connector assignmentCable -V-KX-2 Cable -NPCable -KP, -KP-2, -B-K-2, -B-KP-2, -BV-K-2 Cable -RP-2Cable -DP-2 Cable -B-K-2In compliance with the following requirements WarrantyManufacturer Declarations In compliance withSennheiser electronic GmbH & Co. KG