Samsung Version 1.1 owner manual Setting Other Network Information, Changing IP Address

Page 32

Setting Other Network Information

After successfully setting up the IP address in Ethernet, follow the next procedure to set up additional network information.

After the previous procedure, you must set up the following information, confirmed by the network manager, to connect to network successfully.

●Gateway

●Subnet Mask

●Domain Name

●DNS

(1)Open a web browser (Netscape or Explorer) from the network-connected PC or Unix machine with SNS-110 installed.

(2)Log-in with the SNS-110 IP address set up through the web browser. You must enter the exact ID and password.

The initial user name and password are shown below.

●User Name : root

●Password : w2000

(3)After logged in, set up the additional network information in administration mode.

(4)Be sure to reset or switch off and then switch on your SNS-110 after setting.

Note	Please, refer to Chapter 5 and 7 for Log-in and administration mode network
	setting up.

Changing IP Address

(1)To change the present IP address, log in with the present IP address. Then, change the IP address in network set-up of administration mode.

Refer to Chapter 7. setting Administration Mode Network.

(2)Refer to APPENDIX B "Factory Default", to set up the factory default and set up a new IP address according to Chapter 4, Setting an IP Address.

32

Image 32

Contents

WEB Before You Begin Regulation Approval Table of Contents Administration Mode Overview Functions and FeaturesSNS-110 Overview Page Names and Function Front View of SNS-110Rear of SNS-110 Installing SNS-110 Setting ConfigurationPage 15Cm Surface, due to potential damage on the surface Unpacking Connecting to Instruments VTR, DVDP, TV OUTConnecting to External Instruments VideoConnecting to Network Ethernet10BaseT/100BaseTConnecting to Alarm Sensors and External Devices G 3 4 G RA RC + +Connecting to PAN/TILT/ZOOM/FOCUS Controller That the above PAN/TILT/ZOOM/FOCUS camera and controllersConnecting to RS-232C RS 232C Terminal D-Sub 9Pin RS 232C Connecting to CableCreating RS-232C Cable Terminal Emulation Communication Set-upCreating Ethernet Cable Connected from SNS-110 to PCTwisted CableSetting an IP Address Before You BeginSetting In Ethernet 10BaseT/100BaseT For Windows 95/98/ME/NT/2000/XPSetting up IP address in Ethernet Setting in Unix Setting up an IP address in Ethernet Setting with IP Installer Window Page Page Setting Other Network Information Changing IP AddressCable Network through Cable Modem Log-in through Netscape Ideal SpecificationSNS-110Log-in Log-in through Explorer First TimePage After the First Time Others Single Screen Application Mode Video Image Monitoring ModeInitial Screen Quadruplex Screen Automatic Sequential ScreenSingle Screen with PAN/TILT/ZOOM Controller Administration Mode Camera Set-up PAN/TILT/ZOOM PAN/TILT/ZOOM Set-up Supported, contact your vendorQuad/Sequential Set-up RecommendWeb Transmitter Set-up Password Right after the S/W upgrade, ‘Software Reset’ doesn’t work Setting the Alarm / Relay Out RecommendEnable Network Set-up Between 0~ Page File Transfer Setting Page Custom User Interface Setup ABOUT/ SUPPORT/ Help Page WEB Appendix a SNS-110 Specifications Performance Outside view WEB B Values for setting up SNS-110 Appendix B Factory DefaultHow to Enter the Factory Default Dhcp WEB C Message Appendix C How to Use ConsoleStarting Console Internet Video Server webTX SNS-110 Command Page 5reset SNS-110 »Reset ‰ˆ¯·ˇ· Manual Configuration Mode Page Page Automatically changed to 0. Confirm for more accurate setup WEB D To send IP information to the administrator E-mail Appendix D Dynamic IP Information TransferSelect items? IP notify-mail enable? Y Registering IP information with Administration server Page Page Setting with the Web Browser CGI Program for the Administration ServerWEB E Appendix E FAQ When e-mails are not sent and alarm sets offPage When normally-functioning SNS-110 is suddenly not connecting You cannot use FTP for transfer when setting up FTP transfer E C T R O N I C S