Samsung Version 1.1 owner manual Setting the Alarm / Relay Out, Recommend

Page 50

Setting the ALARM / RELAY Out

(1)Connect the alarm sensor to another device according to the ‘Chapter 3 Connecting to Instruments’. The alarm level of the alarm terminal 1~4 is the following.

●Normal condition : TTL High Level (DC 5V)

●Alarm : TTL Low Level (DC 0V)

(2)If the alarm is set off the SNS-110 sends video images connected to alarm terminal 1~4, by E-mail or to the FTP server on a set time gap. 5 frames for E-mail and 999 frames for FTP can be transferred, and the E-mail with preset messages and video images can also be transferred.

(3)In the Administration Mode this settings window will be seen with a click on the "Alarm/Relay" icon.

(4)Status

The present status on the Relay Out terminal of the reverse side of the SNS-110. The toggle shaped "Turn On/Off" button is used to control the external device connected to the Relay Out terminal.

(5)Sender

In order to send alarm messages and video images by E-mail, the E-mail address must be entered so as to identify the sender. If the E-mail address is invalid the alarm messages and the video images may not be sent as wanted.

Recommend

Please, set the valid e-mail address of SNS-110 administrator at e-mail the ‘sender’.

50

Image 50

Contents WEB Before You Begin Regulation Approval Table of Contents Administration Mode Overview Functions and FeaturesSNS-110 Overview Page Names and Function Front View of SNS-110Rear of SNS-110 Installing SNS-110 Setting ConfigurationPage 15Cm Surface, due to potential damage on the surface Unpacking Connecting to Instruments VTR, DVDP, TV OUTConnecting to External Instruments VideoConnecting to Network Ethernet10BaseT/100BaseTConnecting to Alarm Sensors and External Devices G 3 4 G RA RC + +Connecting to PAN/TILT/ZOOM/FOCUS Controller That the above PAN/TILT/ZOOM/FOCUS camera and controllersConnecting to RS-232C RS 232C Terminal D-Sub 9Pin RS 232C Connecting to CableCreating RS-232C Cable Terminal Emulation Communication Set-upCreating Ethernet Cable Connected from SNS-110 to PCTwisted CableSetting an IP Address Before You BeginSetting In Ethernet 10BaseT/100BaseT For Windows 95/98/ME/NT/2000/XPSetting up IP address in Ethernet Setting in Unix Setting up an IP address in Ethernet Setting with IP Installer Window Page Page Setting Other Network Information Changing IP AddressCable Network through Cable Modem Log-in through Netscape Ideal SpecificationSNS-110Log-in Log-in through Explorer First TimePage After the First Time Others Single Screen Application Mode Video Image Monitoring ModeInitial Screen Quadruplex Screen Automatic Sequential ScreenSingle Screen with PAN/TILT/ZOOM Controller Administration Mode Camera Set-up PAN/TILT/ZOOM PAN/TILT/ZOOM Set-up Supported, contact your vendorQuad/Sequential Set-up RecommendWeb Transmitter Set-up Password Right after the S/W upgrade, ‘Software Reset’ doesn’t work Setting the Alarm / Relay Out RecommendEnable Network Set-up Between 0~ Page File Transfer Setting Page Custom User Interface Setup ABOUT/ SUPPORT/ Help Page WEB Appendix a SNS-110 Specifications Performance Outside view WEB B Values for setting up SNS-110 Appendix B Factory DefaultHow to Enter the Factory Default Dhcp WEB C Message Appendix C How to Use ConsoleStarting Console Internet Video Server webTX SNS-110 Command Page 5reset SNS-110 »Reset ‰ˆ¯·ˇ· Manual Configuration Mode Page Page Automatically changed to 0. Confirm for more accurate setup WEB D To send IP information to the administrator E-mail Appendix D Dynamic IP Information TransferSelect items? IP notify-mail enable? Y Registering IP information with Administration server Page Page Setting with the Web Browser CGI Program for the Administration ServerWEB E Appendix E FAQ When e-mails are not sent and alarm sets offPage When normally-functioning SNS-110 is suddenly not connecting You cannot use FTP for transfer when setting up FTP transfer E C T R O N I C S