Samsung Version 1.1 owner manual PAN/TILT/ZOOM Set-up, Supported, contact your vendor

Page 45

PAN/TILT/ZOOM Set-up

(1) You will see the next window, if you click "P/T/Z" icon in administration mode.

(2)Device

To control PAN/TILT/ZOOM/FOCUS, connect the PAN/TILT/ZOOM/FOCUS camera & controller to the +, - terminals of RS-485 on the rear of your web transmitter. For further information, refer to Chapter 3. "Connecting to PAN/TILT/ZOOM/FOCUS Camera & Controller".

Here are the supported PAN/TILT/ZOOM/FOCUS camera & controller.

●Smart Dome Camera & Controller, made by Samsung Electronics

●P Protocol Dome Camera and Receiver, made by PELCO

●CPU Receiver, made by Sungjin Electronics

Note	If you have a device other than Pan/Tilt/Zoom/Focus controller that is currently
	supported, contact your vendor.

(3)Baud Rate

Set up appropriate Baud Rate depending on the type of controller.

(4)Data Bit

Select Data Bit from either 7Bit or 8Bit, depending on the type of controller.

(5)Stop Bit

Select Stop Bit from either 1 Bit or 2 Bit, depending on the type of controller.

(6)Parity Bit

Select Parity Bit from Odd, Even, or None, depending on the type of controller.

(7)Camera Identity

Maximum of 4 PAN/TILT/ZOOM/FOCUS controllers may be connected. When connecting more than one controller, you must assign an ID for each controller. Please, refer to the controller manual for its ID.

45

Image 45

Contents

WEB Before You Begin Regulation Approval Table of Contents Administration Mode Functions and Features SNS-110 OverviewOverview Page Front View of SNS-110 Names and FunctionRear of SNS-110 Setting Configuration Installing SNS-110Page 15Cm Surface, due to potential damage on the surface Unpacking VTR, DVDP, TV OUT Connecting to InstrumentsVideo Connecting to External InstrumentsEthernet10BaseT/100BaseT Connecting to NetworkG 3 4 G RA RC + + Connecting to Alarm Sensors and External DevicesThat the above PAN/TILT/ZOOM/FOCUS camera and controllers Connecting to PAN/TILT/ZOOM/FOCUS ControllerRS 232C Terminal D-Sub 9Pin RS 232C Connecting to Cable Connecting to RS-232CTerminal Emulation Communication Set-up Creating RS-232C CableConnected from SNS-110 to PCTwisted Cable Creating Ethernet CableBefore You Begin Setting an IP AddressFor Windows 95/98/ME/NT/2000/XP Setting In Ethernet 10BaseT/100BaseTSetting up IP address in Ethernet Setting in Unix Setting up an IP address in Ethernet Setting with IP Installer Window Page Page Changing IP Address Setting Other Network InformationCable Network through Cable Modem Ideal Specification SNS-110Log-inLog-in through Netscape First Time Log-in through ExplorerPage After the First Time Others Application Mode Video Image Monitoring Mode Initial ScreenSingle Screen Automatic Sequential Screen Quadruplex Screen Single Screen with PAN/TILT/ZOOM Controller Administration Mode Camera Set-up PAN/TILT/ZOOM Supported, contact your vendor PAN/TILT/ZOOM Set-upRecommend Quad/Sequential Set-upWeb Transmitter Set-up Password Right after the S/W upgrade, ‘Software Reset’ doesn’t work Recommend Setting the Alarm / Relay OutEnable Network Set-up Between 0~ Page File Transfer Setting Page Custom User Interface Setup ABOUT/ SUPPORT/ Help Page WEB Appendix a SNS-110 Specifications Performance Outside view WEB B Appendix B Factory Default How to Enter the Factory DefaultValues for setting up SNS-110 Dhcp WEB C Appendix C How to Use Console Starting ConsoleMessage Internet Video Server webTX SNS-110 Command Page 5reset SNS-110 »Reset ‰ˆ¯·ˇ· Manual Configuration Mode Page Page Automatically changed to 0. Confirm for more accurate setup WEB D Appendix D Dynamic IP Information Transfer To send IP information to the administrator E-mailSelect items? IP notify-mail enable? Y Registering IP information with Administration server Page Page CGI Program for the Administration Server Setting with the Web BrowserWEB E When e-mails are not sent and alarm sets off Appendix E FAQPage When normally-functioning SNS-110 is suddenly not connecting You cannot use FTP for transfer when setting up FTP transfer E C T R O N I C S