Samsung Version 1.1 owner manual Password

Page 48

③Pswd Enable

Restricts the access from other users. If you check the check box of "Pswd Enable" and click "Apply" button, you should input registered username and its password in Log-in window to access to the Application mode.

If you don’t check the check box of "Pswd Enable", anyone is accessible to the Application mode.

Caution	Anyone, who is accessible to Administration mode, may change configuration
	of SNS-110. If the configuration is deleted or altered, the system may be
	damaged or malfunction. Therefore, factory default is set up with root
	password.
	After the initial installation, you are strongly recommended to change the root
	password and restrict the access from other users.

(4)S/W Upgrade

Upgrade the currently installed program in SNS-110 to the most updated version.

①Download the updated program version from Samsung Electronics web site . (www.samsungelectronics.com), or from SNS-110 service man. The file name of SNS-110 program is sns110_vXXX_XXXX.bin.

②Save the updated program version in the directory of SNS-110-connected PC.

③Click "Browse" and select the updated program, sns110_vXXX_XXXX.bin, in the directory. The selected file will be saved in the browse window.

④Click "Install" and open dialog window. You will see caution message, then click "OK" to start program upgrade. Upon the upgrade completion, you will see another dialog window. You must wait approximately for 2 minutes.

Caution	Wait until the "Upgrading is successful! New code will be loaded after
	reset" message appears. Rebooting SNS-110 before this message can
	cause fatal damage to the machine.

⑤Reboot SNS-110 after the upgrade being completed as shown below.

●Press "Reset" button on the front panel.

●Turn off and then on SNS-110.

⑥After successfully upgrade the program, execute web browser and Log-in.

48

Image 48

Contents

WEB Before You Begin Regulation Approval Table of Contents Administration Mode Functions and Features SNS-110 OverviewOverview Page Names and Function Front View of SNS-110Rear of SNS-110 Installing SNS-110 Setting ConfigurationPage 15Cm Surface, due to potential damage on the surface Unpacking Connecting to Instruments VTR, DVDP, TV OUTConnecting to External Instruments VideoConnecting to Network Ethernet10BaseT/100BaseTConnecting to Alarm Sensors and External Devices G 3 4 G RA RC + +Connecting to PAN/TILT/ZOOM/FOCUS Controller That the above PAN/TILT/ZOOM/FOCUS camera and controllersConnecting to RS-232C RS 232C Terminal D-Sub 9Pin RS 232C Connecting to CableCreating RS-232C Cable Terminal Emulation Communication Set-upCreating Ethernet Cable Connected from SNS-110 to PCTwisted CableSetting an IP Address Before You BeginSetting In Ethernet 10BaseT/100BaseT For Windows 95/98/ME/NT/2000/XPSetting up IP address in Ethernet Setting in Unix Setting up an IP address in Ethernet Setting with IP Installer Window Page Page Setting Other Network Information Changing IP AddressCable Network through Cable Modem Ideal Specification SNS-110Log-inLog-in through Netscape Log-in through Explorer First TimePage After the First Time Others Application Mode Video Image Monitoring Mode Initial ScreenSingle Screen Quadruplex Screen Automatic Sequential ScreenSingle Screen with PAN/TILT/ZOOM Controller Administration Mode Camera Set-up PAN/TILT/ZOOM PAN/TILT/ZOOM Set-up Supported, contact your vendorQuad/Sequential Set-up RecommendWeb Transmitter Set-up Password Right after the S/W upgrade, ‘Software Reset’ doesn’t work Setting the Alarm / Relay Out RecommendEnable Network Set-up Between 0~ Page File Transfer Setting Page Custom User Interface Setup ABOUT/ SUPPORT/ Help Page WEB Appendix a SNS-110 Specifications Performance Outside view WEB B Appendix B Factory Default How to Enter the Factory DefaultValues for setting up SNS-110 Dhcp WEB C Appendix C How to Use Console Starting ConsoleMessage Internet Video Server webTX SNS-110 Command Page 5reset SNS-110 »Reset ‰ˆ¯·ˇ· Manual Configuration Mode Page Page Automatically changed to 0. Confirm for more accurate setup WEB D To send IP information to the administrator E-mail Appendix D Dynamic IP Information TransferSelect items? IP notify-mail enable? Y Registering IP information with Administration server Page Page Setting with the Web Browser CGI Program for the Administration ServerWEB E Appendix E FAQ When e-mails are not sent and alarm sets offPage When normally-functioning SNS-110 is suddenly not connecting You cannot use FTP for transfer when setting up FTP transfer E C T R O N I C S