Samsung Version 1.1 owner manual Enable

Page 51

(6)Enable

Each alarm terminal has to be set as for whether the "Mail" or "FTP" transfer function is going to be used. If the alarm sensor isn't installed or if the input signal can be ignored, click "No".

(7)Pre-alarm

If the video image transfer is set to FTP and the alarm went off, this will send the images that were sent before the alarm. The number of the video images that is sent before the alarm is equal to the 'Image No.' in item (12), and if the Image No. surpasses 32, then a maximum of 32 frames will be transferred.

(8) Receiver

This sets the E-mail address that will receive the alarm messages and the video images when the alarm goes off. It is used when the 'Mail' is set in item (6).

(9) Subject

This sets the 'Subject' of the alarm message, and 30 characters can be entered. It is used when the 'Mail' is set in item (6).

(10)Message

This sets the alarm message it self, 30 characters can be entered. It is used when the 'Mail' is set in item (6).

(11)Camera

This sets the image that will be transferred among Camera 1~ 4 when the alarm goes off.

(12)Image No.

This sets the page number of video images received. If the 'Mail' in item (6) is set, the mail No. is, if the FPT is set the FTP No. is used. Mail can be used 1~ 5, and FTP 1~ 999.

(13)Time Delay

This sets the time gap while the still image is received. If is set for "2 seconds", it transfers one captured cut of still image every 2 seconds and the figure set in item (12) is the number of repetition. When set to "None", no time gap is used and the still image is captured and transmitted by the SNS- 110 with its highest ability.

Caution	If the attached file is blocked or the size is limited when sending an image file on the
	SMTP server, the alarm messages and the video images may not be transferred.

51

Image 51

Contents WEB Before You Begin Regulation Approval Table of Contents Administration Mode Functions and Features SNS-110 OverviewOverview Page Front View of SNS-110 Names and FunctionRear of SNS-110 Setting Configuration Installing SNS-110Page 15Cm Surface, due to potential damage on the surface Unpacking VTR, DVDP, TV OUT Connecting to InstrumentsVideo Connecting to External InstrumentsEthernet10BaseT/100BaseT Connecting to NetworkG 3 4 G RA RC + + Connecting to Alarm Sensors and External DevicesThat the above PAN/TILT/ZOOM/FOCUS camera and controllers Connecting to PAN/TILT/ZOOM/FOCUS ControllerRS 232C Terminal D-Sub 9Pin RS 232C Connecting to Cable Connecting to RS-232CTerminal Emulation Communication Set-up Creating RS-232C CableConnected from SNS-110 to PCTwisted Cable Creating Ethernet CableBefore You Begin Setting an IP AddressFor Windows 95/98/ME/NT/2000/XP Setting In Ethernet 10BaseT/100BaseTSetting up IP address in Ethernet Setting in Unix Setting up an IP address in Ethernet Setting with IP Installer Window Page Page Changing IP Address Setting Other Network InformationCable Network through Cable Modem Ideal Specification SNS-110Log-inLog-in through Netscape First Time Log-in through ExplorerPage After the First Time Others Application Mode Video Image Monitoring Mode Initial ScreenSingle Screen Automatic Sequential Screen Quadruplex ScreenSingle Screen with PAN/TILT/ZOOM Controller Administration Mode Camera Set-up PAN/TILT/ZOOM Supported, contact your vendor PAN/TILT/ZOOM Set-upRecommend Quad/Sequential Set-upWeb Transmitter Set-up Password Right after the S/W upgrade, ‘Software Reset’ doesn’t work Recommend Setting the Alarm / Relay OutEnable Network Set-up Between 0~ Page File Transfer Setting Page Custom User Interface Setup ABOUT/ SUPPORT/ Help Page WEB Appendix a SNS-110 Specifications Performance Outside view WEB B Appendix B Factory Default How to Enter the Factory DefaultValues for setting up SNS-110 Dhcp WEB C Appendix C How to Use Console Starting ConsoleMessage Internet Video Server webTX SNS-110 Command Page 5reset SNS-110 »Reset ‰ˆ¯·ˇ· Manual Configuration Mode Page Page Automatically changed to 0. Confirm for more accurate setup WEB D Appendix D Dynamic IP Information Transfer To send IP information to the administrator E-mailSelect items? IP notify-mail enable? Y Registering IP information with Administration server Page Page CGI Program for the Administration Server Setting with the Web BrowserWEB E When e-mails are not sent and alarm sets off Appendix E FAQPage When normally-functioning SNS-110 is suddenly not connecting You cannot use FTP for transfer when setting up FTP transfer E C T R O N I C S