Samsung SP-H800 manual Indicator Information

Page 9

Indicator Information

: Turned on

: Blinks

: Turned off

TEMP LAMP

STANDBY

Information

If you press the POWER button on the remote control or projector, the screen appears within 30 seconds.

The projector is in normal operating condition.

This state appears when the projector is preparing an operation after the POWER button on the projector or the remote control has been pressed.

The POWER button is pressed to turn off the projector, and the cooling system is in operation to cool off inside of the projector. (Lasts for about 1 minute and 30 seconds)

Refer to measure 1 below if the cooling fan inside the projector is not in normal operation condition.

Refer to measure 2 below if the lamp cover protecting the lamp unit is not closed properly.

Power is turned off automatically when temperature inside of the projector goes beyond the control limit. Refer to measure 3.

Refer to measure 4 below if the life span of the lamp is running out or a problem with the lamp is detected.

Clearing Indicator Problems

Classification

State

Measures

 

 

 

Measure 1

When the cooling fan system is

If the symptom remains even after disconnecting and then

 

not in normal operating condition.

reconnecting the power cord and turning the projector on

 

 

again, contact your product provider or our service center.

Measure 2

When the lamp cover protecting

Check the screw on the bottom side of the projector. If you

 

the lamp unit is not properly

do not find any problem, contact a dealer or service

 

closed or the sensor system is not

personnel near you.

 

in normal operating condition.

 

 

 

 

Measure 3

When temperature inside of the

Adjust the position of the projector following the

 

projector becomes too high.

installation instructions of this manual and cool off the

 

 

projector before restarting it. If the problem does not

 

 

disappear, contact a dealer or service personnel near you.

Measure 4

The lamp is malfunctioning after

Turn the power off, wait for a sufficient amount of cooling

 

abnormal power off or restarting

time and then turn the power on for operations.

 

right after turning off the projector.

 

 

When brightness of the picture

Check how long the lamp has been used on Information

 

screen degrades or image

and contact a dealer or service personnel near you for lamp

 

deterioration is found.

replacement.

 

This Projector uses a cooling fan system to keep

 

the unit from overheating.

NOTE

Operation of the cooling fan may cause noise,

 

 

which does not affect the product performance.

 

No exchange or refund for the noise concern.

 

 

Preparation

Projector and Accessories

9

Page 8 Page 10
Image 9
Page 8 Page 10
Contents Owners Instructions Table of Contents Troubleshooting Optical engine adopting advanced DLP technology Features and DesignProjector Lamp Page Preparation Front/Upper Side and Accessories Indicator Information Rear Side Rear Side and CablesKeystone Remote Control ButtonsOperating Move/Select Button Operating the Remote ControlUsing Remote Control in Dark Place Light To Install the Projector InstallationTurning On Projector Turning ON/OFFUsing the Zoom Knob and the Focus Ring Zoom and Focus AdjustmentLeveling with Adjustable Feet Using the Lens Shift Dial Using the Lens Shift DialScreen Size and Projection Distance Page Connections and Source Setup Before Connections Check the following Before ConnectingConnecting to VCR/Camcorder/Cable Box Connecting to Video Equipment Connecting to DVDConnecting to the Digital TV Receiver Setting up the External Input Source Naming the External Connections Picture Adjustment Picture Adjustment Selecting Picture Mode Selecting Picture ModeSettings for Each Picture Mode Custom Settings of the Picture Custom Settings of the PictureCustom Picture Menu Changing the Color Standard Changing the Color StandardColor Temperature Selecting and Adjusting Color TemperatureGamma Mode Gamma CorrectionGamma Correction Settings Saving Custom Picture SettingsSetting up DNIe Setting up DNIeDNIe Mode Selecting Picture Size Selecting Picture SizeSupported Picture Sizes Picture Adjustment Selecting Picture SizeScreen Position Adjustment Screen Position AdjustmentSelecting Noise Reduction Selecting Noise ReductionColor Control Mode Color ControlColor Control Film Mode Film ModeOverscan OverscanSetting the Black Level Setting the Black LevelBlack Level Modes Still Picture Page Setup Flipping/Reversing the Projected Image Install MenuLight Setting SetupLight Setting Mode Correcting V-Keystone Correcting Vertical KeystoneTest Pattern Menu Test PatternsRestoring the Factory Default Settings Press the Info button InformationLED Operating Modes Setting the LEDMenu Option Menu Option Setting the LanguageSetting the Menu Position Setting the Menu Translucency Setting the Menu TranslucencySetting Up the Menu Display Time Selecting the Quick Menu Connecting to PC Display modes supported by this projector Before Connecting to PCTable supported by this projector Setting up the PC EnvironmentUsing PC Video Cable or DVI Cable Connecting to PCVesa Plug & Play Pin Configuration of PC Video Port PlugAutomatic Picture Adjustment Automatic Picture AdjustmentFrequency Adjustment Fine Tuning with the Phase Adjustment Zooming the Screen Reset the PC Reset the PCTroubleshooting Before Contacting Service Personnel Before Contacting Service PersonnelScreen and External Source Page Other Information Cleaning the Projector and Lens Storage and MaintenanceOptional Parts Purchasing Optional PartsGlossary Gamma Mode Antenna in PortDLP HD2+, DC3 Structure of Screen Menu Select Composite/S-Video/Component Input ModeLED Structure of Screen Menu Lamp Replacement Procedure Lamp ReplacementRS-232C Connection and Control Commands Classification Model SP-H800 SpecificationsFunction and Transmission Codes Remote Control Specifications
Top Page Image Contents