Samsung ML-3050 manual Printing a demo, Changing the display language ML-3051N,ML, Network menu

Page 19

Network menu

This menu lets you configure the network interface installed in your printer. You can reset the network interface and print a configuration page.

Item

Explanation

 

 

TCP/IP

Values: DHCP, BOOTP, Static

 

This item allows you to manually set the TCP/IP addresses or receive the addresses from the network.

•DHCP: The DHCP server allots the IP address to you automatically.

•BOOTP: The BOOTP server allots the IP address to you automatically.

•Static: You can enter IP address, subnet mask, and gateway manually.

EtherTalk

Values: Off, On

 

 

This item lets you select whether or not you use the

 

EtherTalk protocol. Select On to use the protocol.

NetWare

Values: Auto, 802.2, 802.3, Ethernet II, SNAP, Off

 

 

This item lets you select the IPX frame type.

•Auto: You can set the frame type automatically.

•802.2: Select this value to use the IEEE 802.2 frame type.

•802.3: Select this value to use the IEEE 802.3 frame type.

•Ethernet II: Select this value to use the Ethernet 2 frame type.

•SNAP: Select this value to use the SNAP frame type.

•Off: You can disable the NetWare protocol.

Ethernet

Values: Auto, 10M Half, 10M Full,

Speed

100M Half, 100M Full

 

This item allows you to select the ethernet speed.

Wireless

Values: WLAN Basic, WLAN Security, WLAN Default

 

Configure the wireless network environments.

See page 10.3.

Note

This menu only appears when an optional wireless network interface card has been installed.

Item

Explanation

 

 

Clear

This item performs a simple reset and restores the

Setting

factory default settings for the network

 

configuration. This setting will only take effect after

 

you have reset the printer.

 

 

Network

This item print a page showing the network

Info

parameters you set.

 

 

Printing a demo page

Print a demo page to make sure that the printer is operating correctly.

ML-3050, ML-3051N

Press and hold Demo for about 2 seconds.

ML-3051N, ML-3051ND

1Press Menu and then OK when Information appears.

2Press the Scroll buttons until Demo Page appears and press OK. A demo page prints out.

Changing the display language (ML-3051N,ML-

3051ND only)

To change the language that is displayed on the control panel, follow these steps:

1Press Menu until System Setup appears on the bottom line of the display and press OK.

2Press OK when Language appears.

3Press the Scroll buttons to select the language you want and press OK.

4Press Stop to return to Standby mode.

2.6 <System setup>

Page 18 Page 20
Image 19
Page 18 Page 20
Contents Page Page Country Customer Care Center Web Site Contact Samsung World WideContents Specifications MaintenanceTroubleshooting Installing accessoriesImportant Precautions and Safety Information Federal Communications Commission FCC FCC Statement for Wireless LAN useFCC Regulations Canadian Radio Interference RegulationsWireless Guidance European States qualified under wireless approvalsEuropean States with restrictions on use Replacing the Fitted Plug for UK Only You can print in Windows 95/98/Me/NT 4.0/2000/XP/2003 Special featuresSpecial features Printer overview Finding more information IntroductionPrinter overview Features ML-3050 ML-3051N ML-3051NDFront view ML-3051N and ML-3051ND Rear view Control panel overviewSelecting a location Finding more informationClearance space Menu overview System setupUsing control panel menus ML-3051N,ML-3051NDonly Accessing control panel menusLayout menu Information menuGraphic menu Paper menuEmulation menu System Setup menuPostScript ML-3050, ML-3051N Printing a demoChanging the display language ML-3051N,ML Network menuUsing the control panel button Using toner save modeFrom the software application Supplied software Software overviewWindows Printer driver featuresFeature System requirementsMacintosh LinuxRequirements Supported operating systems Network setupConfiguring TCP/IP Via network administration programsStatic addressing Configuring EtherTalkConfiguring IPX frame types Dynamic addressing BOOTP/DHCPRestoring the network configuration Setting Ethernet speedPrinting a network configuration Selecting print media Loading print mediaSupported sizes of paper Type Size Dimensions Weighta CapacitybGuidelines for special print media Guidelines for selecting and storing print mediaMedia type Guidelines Loading paper Changing the size of the paper in the tray Using the tray 1 or the optional trayLoad the paper with the side to be printed on facing up Using the multi-purpose trayTips on using the multi-purpose tray Using manual feed modePrinting to the output tray Face down Selecting an output locationPrinting to the rear cover Face up Printing a document Canceling a print jobPrinting a document Canceling a print job Basic printingHow to purchase Accessories Ordering supplies and accessoriesToner cartridges Cleaning the inside of the printer MaintenanceCleaning the printer Cleaning the outside of the printerChecking the remaining toner Maintaining the toner cartridgeOpen the front cover Pull the toner cartridge out Redistributing toner cartridgeReplacing the toner cartridge Toner Low appears on the display. ML-3051N,ML-3051ND onlyClearing the Toner Low Replace Toner message Maintenance partsItems Yield Average Tray TroubleshootingClearing paper jams Paper feed areaMulti-purpose tray Optional trayPaper exit area Around the toner cartridgeDuplex jam Duplex unit area ML-3051NDonlyTips for avoiding paper jams Status Description Troubleshooting checklistCondition Suggested solutions Understanding the Status LEDUnderstanding display messages Toner cartridge-related messages Solving general printing problems Series PCL 6 printer icon Settings and Printers. RightSpool Settings button Click the Samsung ML-3050Solving print quality problems Characters Condition Suggested solutions BackScatter MisformedCommon PostScript problems Common Windows problemsCommon Macintosh problems Common Linux problemsDisconnect the power cord Installing accessoriesPrecautions when installing accessories Installing a memory DimmSetting the memory in the PostScript printer properties Installing a wireless network interface cardSelect the Samsung ML-3050 Series PS printer Configuring basic network settings Configuring the wireless network parametersSetting Encryption Selecting the authentication typeHexadecimal Alphanumeric Specifications and Description SpecificationsPrinter specifications Printer specificationsIndex System requirements Linux 3.3 Macintosh 3.3 Windows Software section Contents Using Windows Postscript Driver Using Your Printer with a Macintosh Select Typical installation for a local printer. Click Next Installing Printer SoftwareInstalling Software for Local Printing Typical InstallationCustom Installation Select Custom installation. Click Next Installing Software for Network Printing Custom Installation Installing Printer Software in Windows Changing the Software Language Reinstalling Printer SoftwareNext Removing Printer SoftwareSelect your printer driver from the Name drop-down list Printing a DocumentLayout Tab Printer SettingsPaper Orientation Source Paper TabScaling Printing Graphics Tab Image ModeResolution Toner Save ModeAbout Tab Extras TabPrinter Tab Using Help Using a Favorite SettingPrinting Multiple Pages on One Sheet of Paper N-Up Printing Advanced PrintingPrinting Booklets Printing PostersNone Printing on Both Sides of PaperPrinting a Reduced or Enlarged Document Fitting Your Document to a Selected Paper SizeEditing a Watermark Using WatermarksUsing an Existing Watermark Creating a WatermarkCreating a New Page Overlay Using OverlaysWhat is an Overlay? Using a Page OverlayAdvanced Using Windows PostScript DriverSelect Local Port and click New Port Setting Up a Host ComputerSetting Up a Client Computer Check the Share this printer boxToner Level Troubleshooting GuidePrinter Setting Understanding Smart PanelUsing Onscreen Help File Opening the Troubleshooting GuideUsing Printer Settings Utility Changing the Smart Panel Program SettingsInstalling the Unified Linux Driver Installing the Unified Linux DriverGetting Started Click Uninstall Using the Unified Driver ConfiguratorUninstalling the Unified Linux Driver Opening the Unified Driver ConfiguratorClasses Tab Printers ConfigurationPorts Configuration Printers TabPrinting from Applications Configuring Printer PropertiesPrinting Files ML-3050 only Installing printer driver for MacintoshInstall the Printer driver Uninstalling the Printer driverSelect Socket/HP Jet Direct in Printer Type Setting Up the PrinterFor a Network-connected Macintosh For a USB-connected MacintoshPrinting a Document Changing Printer SettingsLayout Setting PrintingReverse Duplex Printer Features SettingResolutionQuality Printing Multiple Pages on One Sheet of PaperDuplex Printing Index Macintosh 31 uninstall Rev
Top Page Image Contents