Samsung ML-4050ND Using manual feed mode, Tips on using the multi-purpose tray

Page 33

4Squeeze the multi-purpose tray paper width guides and adjust them to the width of the paper. Do not force too much, or the paper will be bent, which will result in a paper jam or skew.

5When you print a document, set the paper source and type in the software application. See the Software section.

For information about setting the paper source and type on the control panel, see page 2.3.

6After printing, put the multi-purpose tray extension back to its place and close the multi-purpose tray.

Tips on using the multi-purpose tray

•Load only one size of print media at a time in the multi-purpose tray.

•To prevent paper jams, do not add paper when there is still paper in the multi-purpose tray. This also applies to other tray.

•Print media should be loaded face up with the top edge going into the multi-purpose tray first and be placed in the center of the tray.

•Always load only the print media specified in page 5.2 to avoid paper jams and print quality problems.

•Flatten any curl on postcards, envelopes, and labels before loading them into the multi-purpose tray.

•When you print on 76 mm x 127 mm (3 x 5 inches) sized media on the multi-purpose tray, open the rear cover for straight paper path to avoid paper jams.

•When you print on transparencies, open the rear cover. If not they may tear while exiting the printer.

Using manual feed mode

You can manually load a sheet of print media in the multi-purpose tray if you select Manual Feed in the Source option from the Paper tab when you change print settings to print a document. See the Software section. Manually loading paper can be helpful when you want to check the print quality after each page is printed.

This loading procedure is almost the same as the procedure for loading in the multi-purpose tray, except you load paper sheet-by-sheet in the tray, send print data to print the first page, and press Stop on the control panel to print each following page.

1 Load the paper with the side to be printed on facing up.

2Squeeze the multi-purpose tray paper width guides and adjust them to the width of the paper. Do not force too much, or the paper will be bent, which will result in a paper jam or skew.

3When you print a document, set the paper source to Manual Feed and select the appropriate paper size and type in the software application. See the Software section.

4Print a document.

The display shows a message prompting you to load paper and press Stop.

5Press Stop.

The printer picks up the print media and prints. After one page is printed, the message appears again.

Note

• If you do not press the button, after a pause the printer will automatically pick the print media.

6Insert the next sheet into the multi-purpose tray and press Stop. Repeat this step for every page to be printed.

5.7 <Loading print media>

Page 32 Page 34
Image 33
Page 32 Page 34
Contents Page Page Country Customer Care Center Web Site Contact Samsung World WideContents Troubleshooting Installing accessoriesSpecifications Important Precautions and Safety Information Safety and Regulatory InformationEnvironmental and Safety Consideration Laser Safety StatementPower Saver Ozone SafetyRecycling Radio Frequency EmissionsDeclaration of Conformity European Countries United States of AmericaWireless Guidance Regulatory Compliance StatementsReplacing the Fitted Plug for UK Only Special features IntroductionSoftware section Print in various environments Front view Printer overviewControl panel overview Finding more informationClearance space Selecting a locationSystem setup Using control panel menusAccessing control panel menus Menu overview Job manager menuInformation menu Paper menu Layout menuGraphic menu System Setup menuPostScript Emulation menuUsing toner save mode Printing a demoChanging the display language Software overview ContentsSupplied software Postscript Printer Description PPD file UsePrinter driver features System requirementsWindows Macintosh LinuxNetwork setup Via network administration programsVia the control panel Configuring EtherTalk Configuring TCP/IPDynamic addressing BOOTP/DHCP Supported operating systemsSetting Ethernet speed Configuring IPX frame typesRestoring the network configuration Printing a network configurationSelecting print media Loading print mediaType Size Weight Type Size Dimensions Weighta CapacitybSupported sizes of paper Print media for duplex printingGuidelines for selecting and storing print media Guidelines for special print mediaMedia type Guidelines Loading paper Changing the size of the paper in the tray Using the standard tray or the optional traysLoad the paper with the side to be printed on facing up Using the multi-purpose trayTips on using the multi-purpose tray Using manual feed modeSelecting an output location Printing to the output tray Face downPrinting to the rear cover Face up Printing a document Canceling a print job Canceling a print jobBasic printing Printing a documentOrdering supplies and accessories AccessoriesToner cartridges How to purchase Cleaning the printer MaintenanceCleaning the outside of the printer Cleaning the inside of the printerPTL lens Checking the remaining toner Maintaining the toner cartridgeRedistributing toner cartridge Replacing the toner cartridge Maintenance parts Clearing the Toner Low Replace Toner messageItems Yield Average Clearing paper jams TroubleshootingPaper feed area TrayOptional tray Multi-purpose tray Around the toner cartridgePaper exit area Duplex unit areaDuplex jam Troubleshooting checklist Condition Suggested solutionsTips for avoiding paper jams Understanding display messages Understanding the status LEDLow Heat Error Message Meaning Suggested solutions LoadLSU Motor Error OPC is CleaningToner cartridge-related messages Solving general printing problems Spool Settings button Settings and Printers. RightClick the Samsung ML-4050 Series PCL 6 printer iconSolving print quality problems Repetitive Condition Suggested solutions VerticalDefects ScatterCommon PostScript problems Common Windows problemsCommon Macintosh problems Common Linux problemsInstallable Options section to InstalledPrecautions when installing accessories Installing accessoriesInstalling a memory Dimm Disconnect the power cordSetting the memory in the PostScript printer properties Select the Device Settings tabSelect the Samsung ML-4050 Series PS printer Removing a Dimm Installing a wireless network interface cardConfiguring the wireless network parameters Configuring basic network settingsSelecting the authentication type Installing the hard disk Using the hard diskSetting Encryption Restoring default values for wireless networkingSetting the time and date Setting the hard disk in the printer propertiesPrinting with the optional hard disk Storing a jobDeleting a stored job Printing a stored jobControlling the active job queue To delete a file from the queuePrinting using the form files To promote a file from the queueTo print a file immediately Specifications Printer specificationsSpecifications and Description Index System requirements Linux 3.3 Macintosh 3.3 Windows Software section Contents Using Windows Postscript Driver Using Your Printer with a Macintosh Installing Printer Software Installing Software for Local PrintingTypical Installation Select Typical installation for a local printer. Click Next Custom InstallationSelect Custom installation. Click Next Installing Software for Network Printing Installing Printer Software in Windows Custom Installation Installing Printer Software in Windows Select the components you want to reinstall and click Next Reinstalling Printer SoftwareNext Removing Printer SoftwareSelect your printer driver from the Name drop-down list Printing a DocumentPrinter Settings Layout TabPaper Orientation Paper Tab SourceScaling Printing Resolution Image ModeToner Save Mode Graphics TabJob Setting On the Job SettingExtras Tab Using Help Using a Favorite SettingAbout Tab Printer TabPrinting Multiple Pages on One Sheet of Paper N-Up Printing Advanced PrintingPrinting Booklets Printing PostersPrinting a Reduced or Enlarged Document Printing on Both Sides of PaperFitting Your Document to a Selected Paper Size NoneUsing an Existing Watermark Using WatermarksCreating a Watermark Editing a WatermarkWhat is an Overlay? Using OverlaysUsing a Page Overlay Creating a New Page OverlayAdvanced Using Windows PostScript DriverOverview Direct Print Utility PrintingFrom the Direct Print Utility window Setting Up a Client Computer Setting Up a Host ComputerCheck the Share this printer box Select Local Port and click New PortPrinter Setting Troubleshooting GuideUnderstanding Smart Panel Toner LevelUsing Printer Settings Utility Opening the Troubleshooting GuideChanging the Smart Panel Program Settings Using Onscreen Help FileInstalling the Unified Linux Driver Installing the Unified Linux DriverGetting Started Click Uninstall Uninstalling the Unified Linux DriverPrinters Configuration Using the Unified Driver ConfiguratorOpening the Unified Driver Configurator Double-clickUnified Driver Configurator on the desktopConfiguring Printer Properties Ports ConfigurationClasses Tab Printing Files Printing from ApplicationsInstall the Printer driver Installing Software for MacintoshUninstalling the Printer driver Click ContinueFor a Network-connected Macintosh Setting Up the PrinterFor a USB-connected Mac OS 8.6 ~Changing Printer Settings Layout SettingPrinting a Document ResolutionQuality Printer Features SettingPrinting Multiple Pages on One Sheet of Paper Reverse DuplexDuplex Printing Index Image mode 15 resolution Macintosh GGGGGGGGGGGGGRev.9.00
Top Page Image Contents