Mitsubishi Electronics DX-TL950E Auto SET UP / Initial settings, Initialization, HDD Setting

Page 18

AUTO SET UP (continued) / Initial settings

The <RECORD SETTING> screen consists of 2 pages. The second page is displayed when turning the JOG dial to move the cursor to “NEXT PAGE”, and turn the SHUTTLE ring clockwise.

<RECORD SETTING> 1/2

Camera selection during alarm recording

<RECORD SETTING> ALARM CH

NO

PPS

GRADE

A-PPS

A-GRADE

>> 1

12.5P

SUPER

12.5P

SUPER

2------ SUPER ------ SUPER

3------ SUPER ------ SUPER

4 12.5P SUPER 12.5P SUPER

5------ SUPER ------ SUPER

<ESTD

REC>

D H M

NEXT

PAGE

 

INITIALIZATION

Please perform initialization, when a <INITIALIZATION> setup is changed.

1.Turn ON the MAIN switch on the rear of the unit, and wait until the ACCESS indicator goes off. Hold down the REC/STOP button, and press the POWER button on the front of the unit.

The unit starts-up, and the <INITIALIZATION> screen is appears.

POWER button operation will not be accepted while the ACCESS indicator is flashing. Press the POWER button after the indicator turns off.

2.Select “INITIALIZATION” by turning the JOG dial, and turn the SHUTTLE ring clockwise.

The setting is made, and the display returns to normal after initialization.

<RECORD SETTING> 2/2

<RECORD SETTING>

A-GRADE

NO

PPS

GRADE A-PPS

>> 6

------

SUPER

------

SUPER

7

12.5P

SUPER

12.5P

SUPER

8------ SUPER ------ SUPER

9------ SUPER ------ SUPER

<ESTD REC>

D H M

PRESS POWER BUTTON TO EXIT

According to the number of the cameras connected and the value of “RECORDING CYCLE”, the most suit- able setting of the “PPS”, “A-PPS”, “GRADE” and “A- GRADE” are set automatically.

12.When the setting is complete, press the POWER button.

“SETTING UP...” is displayed on the screen, and the unit starts-up.

To execute AUTO SET UP again, press and hold the camera number button 1 and press the POWER button, when the MAIN switch is set to ON and the POWER button is set to OFF. The <CAMERA CHECK> screen appears. However all menu of record setting will be reset.

INITIALIZATION

The <INITIALIZATION> setting is used to select the mode of peripheral recording devices connected to SCSI connector ID4ID5, to make HDD SETTING, and to initialize the HDD.

HDD SETTING

The HDD SETTING can be set to MIRRORING (simulta- neous recording to the internal HDD as a pair), PARTITION (an independent partition that can be set within the total HDD memory specifically for ALARM RECORDING). ( see pages 74,75 “MIRRORING”, “PARTITION”)

<INITIALIZATION>

NORMAL

>>HDD SETTING

POWER OFF

INITIALIZATION

Settings are not confirmed unless you perform

“INITIALIZATION”.

Performing “INITIALIZATION” initializes all data on the HDD. It deletes the complete ALARM LIST, and the next entry is registered from 00001.

Select “POWER OFF” to abort initialization.

ALL DATA WILL BE ERASED

WHEN PROCEED INITIALIZATION

••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••

AUTO SET UP / Initial settings

18

Image 18
Contents DX-TL950E Recording FeaturesBuilt-in duplex 9 channel multiplexer NetworkEase of use Auto set-upProtect the Power Cord When not in use always turn OFF the Main switchMains Lead Connection Contents 67-71 60-6365,66 72,73Flowchart Flowchart for connection and settingsAuto SET UP Setting the timer recording Setting other various functionsSetting the motion detection Timer recording is executed/completedMajor operations and their functions Analogue OUT connectors Emergency indicatorLock indicator Front View Inside of the doorMajor operations and their functions Alarm Interrupt buttonSET UP button Search buttonCamera in connectors Main switchVideo OUT connectors Camera OUT connectorsRS-232C connector Ethernet connectorConnecting to Cctv camera, monitor, sensor ConnectionsAlarm Recording Connection Connecting with analog video recorderConnections Auto SET UP Turn the Shuttle ring clockwiseWhen the setting is complete, press the Power button Auto SET UP / Initial settingsHDD Setting InitializationMenu settings Basic OperationsMultiplexer functions Time Date Adjust Daylight SAVING/DAYLIGHT SettingDefault SUN, LAST, MAR Basic OperationsBasic manual recording Present time displayRecorded capacity display function SUPER, HIGH, STDSTANDARD, BASIC, Long ShortLong To change HDD or Compact Flash Card playback device Basic playbackBack repeatedly see HDD Repeat PLAY, Press the Play buttonTo pause playback, press the Pause button Basic searchTime Date Search To stop playback, press the Stop buttonEnglish , Francais , Deutsch For playback, see Various playback func- tions, pages 65,66Language Selection Españ OL, PyCCKNN, ItalianoMain Menu Menu SettingMenu functions SUB MenuSET UP Initial SET UP/INFORMATION HDD Settings Menu functionsMain Menu SUB Menu REC/STOP + Power button Copy Menu Search Selection MenuCamera TITLE/MEMO Setting Time Date AdjustDisplay Mode Clock Location SettingRepeat steps 2 ~ 6 to input Counter in the camera number Camera TITLE/MEMO Setting screen appearsDisplay returns to the Camera TITLE/MEMO Setting screen Appears in reversed color on the very left of the stringDuplex Mode Display Setting default BottomSPLIT/SEQUENCE button operations Plexer can also be found on seeCamera number button operations Available modesMPX Display Settings ZoomSPLIT9 Screen Setting MPX Display SettingsSPLIT4 Screen Setting For the SPLIT9 Screen SETTING, SPLIT9 screen can be setSequence Setting Interlace3 , 4 , 5 , 6 , 7 Selection Camera Number Detection Mask SettingSetting default 3 , 4 , 5 , 6 , 7 , 8 Nected camera, are setSensitivity Motion Detection SettingsTest Mode Motion ThresholdWhen setting the camera selection during alarm recording Settings concerning normal recording and alarm recordingIng pre-alarm recording, see Alarm SettingRecord Settings About alarm recordingPicture quality for normal recording pages 22,23 Recording time during alarm recording can be set Alarm REC DurationPRE Alarm REC Pre-alarm recording can be setTimer Program Settings Timer ProgramStructure of the Timer Program screen Press the Timer button Cerning recording mode settings, see pages 22,23 Timer Program SettingsHoliday Setting Overlapping Timer settingsHDD Repeat Play HDD Settings HDD Repeat REC MAIN/HDD Repeat REC SUBSetting default OFF IM-CHECK PlayAudio Recording Initial SET UP/INFORMATIONSequential Play Single screen sequential playback startsRear Terminal Settings Mode OUT 1 ~ Mode OUT KEY SoundBuzzer Call OUT Settings Setting of Device default MainSetting of Remain HDD default 10% Remain HDDHDD Main FULL/HDD SUB Full Communication Port SettingsRS-232C Emergency REC DurationSettings EthernetMail Address Service Port Setting Alarm Notification SettingINFORMATION/SERVICE 2/2 INFORMATION/SERVICEINFORMATION/SERVICE 1/2 Setting is confirmed and stops flashingReset to Factory Settings Menu screen settings are reset Menu screen settings are resetData Clear Password Password LockSimple Lock To unlock the Password for level Press the SET UP button To unlock the PasswordInput the Password entered in First in Second Repeat steps 2-2 ~ 2-4 to set level 2 and levelTo change the Password Changing from Password Lock mode to Simple Lock modeTo lock the Password only level1 to level Press the Warning Reset buttonTo save menu settings of this unit to a Compact Flash Card Quick SettingsTo update menu settings of this unit Quick Settings screen appearsOperation example SettingOperation examples OperationHoliday Setting 31/12, 01/01, 02/01, 03/01 This example uses the holiday settingHDD Settings screen setting see pages 47,48 Camera number 1 ~ Input titleRecord Setting C screen setting see REC Mode C screen setting seeAlarm Setting C screen setting see Operation examplesRecord Setting C REC Mode D screen setting seeRecord Setting D screen setting see Alarm Setting DVarious recordings PRE Alarm RecordingsPre-alarm recording Emergency RecordingsVarious playback functions Simultaneous playback during recording Press the REV. Play Reverse Playback buttonVarious search Search SelectionTime Date Search Press the Search button Index SEARCH/ALARM Index SearchVarious search Playback the search resultAlarm Skip Search Alarm Skip Search In the case of forward directionTo clear the search screen, press the Search button twice Alarm List Search To clear the alarm list, erase the dataSTART/END Search Press either the Play REV. Play or Pause buttonSearch screen selected in previous Search Type appears Making Copy/Restore Menu changes to Restore when CFC Main HDD is selectedAn end. Be careful Video Cord Audio Cord Copying from unit to videotapeBack see Sequential PLAY, Analogue Video Cassette RecorderHDD Setting Power failure compensation circuitPower failure reset recording Other convenient functionsPartition Size setting appears on the Initialization screen Points to be aware of regarding Mirror modePoints to be aware of regarding Partition mode PARTITION/PARTITION SizeCovert Camera Setting screen appears Covert Camera SettingAlarm Display Other convenient functionsCommunications by Web Browser AuthenticationCommunications by Web Browser Personal computer product requirementsCommunications by Web Browser WelcomeLive monitor Stop PlaybackTime Search Alarm SearchUser maintenance Select the date and time and click SearchCovert Camera Setting Log outChange log in user Logged in user is changed and the Welcome screen appears HDD continuous recording time for 250GB drive Recording time tableContinuous recording time table Without Audio recordingRecording time table Compact Flash Card continuous recording time for 64MBTroubleshooting Description of problem Please consult the followingTroubleshooting Detection Mask Setting ?Main Image Modified Glossary GlossaryGND SpecificationsConnectors Call OUT/CALL OUT GND
Related manuals
Manual 90 pages 24.16 Kb