Mitsubishi Electronics CP700E Installing the lithium battery, Setting the present time

Page 6

3. Preparations before operation

1 Removing the fixed screw on the printing unit and protective cushion	Pages 5 - 6

2 Installing the lithium battery	Page 6

,Power for memorizing the day and present time are supplied by a lithium battery. Before using this unit install the lithium battery.

3 Installing the print paper and ink cassette.

Pages 7 - 9

,Install the print paper.

,Install the cassette with ink sheet.

4 Setting the present time

Pages 10 - 13

,Set the day and present time to print on the lower part of the print.

1 Removing the fixed screw on the printing unit and protective cushion

When using the unit for the first time, remove the fixed screw on the printing unit and protective cushion.

1Remove the fixed screw on the printing unit.

,There is a fixed screw at the bottom of the printing unit.

1Remove the fixed screw with a screwdriver or coin.

2 Set the removed screw to the hole on the rear panel for keep the screw.

Stored position

1 2

RS-232CREMOTE

VIDEO

S-VIDEO

R G/G+SYNC B H+V-SYNC

IN

OUT

R G/G+SYNC B H+V-SYNC

AC LINE

IMPEDANCE

RGB 75Ω

HIGH

SYNC.

75Ω

HIGH

Fixed screw

Attention:

,Keep the removed fixed screw by setting it to the hole on the rear panel. This screw is required when transporting this unit.

,Make sure you set the fixed screw to the bottom of the unit when transporting the printer.

5

Image 6

Contents CP700E Contents Precautions Power RequirementPrecautions Be Careful with the Printing UnitSafety Checks Setting the present time Installing the lithium batteryInstalling the print paper and ink cassette Remove the fixed screw on the printing unitInstalling the lithium battery Preparations before operationInstalling print paper and ink sheet Installation procedure of print paperInstall the ink sheet Install the ink cassette1Set the printing unit Precautions before printing After printingMenu display Main MenuSetting the present time Setting the day and present timeSetting the present time Change the date and present time setting ChangeConnection with Monitors Connection with RGB Analog Signal equipmentConnection with external equipment Connection with RS-232C equipmentConnection with external equipment Monitor Setting the output sync. signal Output Sync OFFVideo Video signalConnection with external equipment VIDEO/S-VIDEO VCPConnection with external equipment RGB Analog signal Setting the switchesSetting Baud Rate Displaying the menu screenDisplaying System Set Menu Setting the RS-232C Command Type Connection with external equipment RS-232C InterfaceRS-232C Data Signal Features and functions Front PanelFeatures and Functions Inside of Printing UnitPotential equalization connector Rear PanelRemote Control Color AdjustPrint button Printing procedures Basic prints PrintingContinuous printing Selecting Field or Frame Printing Procedures Basic printsPrinting FIELD/FRAMESelecting input signal Press the SET button Main Menu is displayed 1Setting print size S/L Save PRG Memory Storing images in memory / Printing the images Image memorizing with page INC Page Increment functionContinuous printing Setting the number of printsCancelling continuous printing E L DChanging the number of prints during printing Setting the functions Setting the functions OperationButton function setting display Main Menu Memory SW menu Displaying the sub menu Displaying menu screenMemory SW Menu sub menu display Y L O C KSET Setting the functions Main menu FunctionMain Menu Adjusting the color of the image Color ADJFunction Adjust the red-subcontrast of printing image Signal SET Signal selecting menuRGB Same Special print settingAdditional PhotoDeep Print Print settingNML EchoCOM ADJData Making a comment System settingComment SystemSetting the image size 1USER Size ADJSetting the functions Making a comment Making a commentRemote control function on the comment display Menu displayComment making procedure Editing commandInputting the letter Selecting comment blockCase of deleting E Close the comment menu Change OK / CANCEL/ Init Setting the functions Memory SW menuSetting Functions Memory SW Menu CancelTime ADJ Setting the day and present time Setting the buttons functionKEY SET Signal ADJ Signal setting displayPrint setting Print SETMargin cut RET Return HighLOW Printing procedures Special prints Following printing is availablePrinting Procedures Special prints Image prints Multi printsAbcd Image size and the number of memory pages ImagesSetting the multi-print menu Multi Prints1Displaying the image from input signal source image Storing images in memory 1Printing the images FieldSetting Photo print menu Photo PrintsDisplaying the image from input signal source image Selecting the sizeSeparate Print Printing the imagesSetting the multi-print and photo-print menus 1Setting the Separate function1Displaying the source image image from the input signal Selecting Field or Frame Setting Strobe function Strobe Prints1Storing images in memory / Printing the images Printing Procedures Special prints Displaying the source image image from the input signal 1Storing images in memoryPressing the Print button Settingtheautomaticintervalprinting1Interrupting strobe memory Automatic interval prints 1 imagePressing the Memory button 1Interrupting automatic interval printsBusy External Remote 2 terminal on the rear panelMemory RemoteCircuit inside the VCP Pin No Remote terminalTiming Chart External Remote 1 terminal on the rear panelTroubleshooting Troubleshooting Overcoming paper jamsBefore calling for service SymptomTroubleshooting Options K65HMSpecifications French Branch Mitsubishi Electric Europe B.V UK BranchGerman Branch Italian Branch