Mitsubishi Electronics CP700E operation manual 1USER Size ADJ, Setting the image size

Page 53

7. Setting the functions (Main menu)

CONVERT
Function	This function is to output the selected input signal in the “INPUT SEL” function on “2. SIGNAL SET”
	menu to the VIDEO/RGB/S-VIDEO output terminal
	ON	Output the selected input signal to the VIDEO/RGB/S-VIDEO
		output terminal
	OFF	Output the signal from the input terminal to the same names
		as the input terminal .

Note: When the selected signal is remarkably different from the standard signal in timing, the signal

may not be converted correctly at output.

BUZZER

Function Sounds the buzzer

The buzzer sounds when one of the control buttons is pressed, so that the setting can be checked.

ON	Sounds the buzzer
OFF	Does not sound the buzzer

1USER SIZE ADJ	Setting the image size

The printing area can be changed and stored in memory as a user setting.

When selecting “USER ADJ” on the “6.SYSTEM” menu. Press the RIGHT shift button, USER SIZE ADJ menu is displayed.

SET

When pressing the SET button after setting, “CHANGE : OK/CANCEL” is selected.

SET

• When selecting “OK” and pressing the SET button, SYSTEM menu is displayed.

H-POSI

Function Change the horizontal start position of input signal.

Move the image by changing the horizontal position setting area -10 to +10.

When special setting is set to “ON” in Memory SW menu, the setting area of H-POSI is - 65 to +10.

•As the value is decreasing to the minus limit, the switching between memorized image and source image may be impossible during printing.

COPY

Function Copy “SIZE” in the “6.SYSTEM” menu.

Copy an image size set at W, M, N in the “6.SYSTEM” menu.

The selected value is displayed from TOP, BOTTOM, LEFT and RIGHT.

The value is the basis of change.

52

Image 53

Contents CP700E Contents Power Requirement PrecautionsBe Careful with the Printing Unit PrecautionsSafety Checks Installing the print paper and ink cassette Installing the lithium batterySetting the present time Remove the fixed screw on the printing unitPreparations before operation Installing the lithium batteryInstallation procedure of print paper Installing print paper and ink sheet1Set the printing unit Install the ink sheetInstall the ink cassette After printing Precautions before printingMain Menu Menu displaySetting the day and present time Setting the present timeSetting the present time Change Change the date and present time settingConnection with external equipment Connection with RGB Analog Signal equipmentConnection with Monitors Connection with RS-232C equipmentConnection with external equipment Monitor OFF Setting the output sync. signal Output SyncConnection with external equipment VIDEO/S-VIDEO Video signalVideo VCPSetting the switches Connection with external equipment RGB Analog signalDisplaying System Set Menu Setting Baud RateDisplaying the menu screen Connection with external equipment RS-232C Interface Setting the RS-232C Command TypeRS-232C Data Signal Front Panel Features and functionsInside of Printing Unit Features and FunctionsRear Panel Potential equalization connectorColor Adjust Remote ControlPrint button Continuous printing Printing procedures Basic printsPrinting Printing Printing Procedures Basic printsSelecting Field or Frame FIELD/FRAMESelecting input signal Press the SET button Main Menu is displayed 1Setting print size S/L Save PRG Memory Image memorizing with page INC Page Increment function Storing images in memory / Printing the imagesCancelling continuous printing Setting the number of printsContinuous printing E L DChanging the number of prints during printing Setting the functions Operation Setting the functionsButton function setting display Main Menu Memory SW menu Memory SW Menu sub menu display Displaying menu screenDisplaying the sub menu Y L O C KSET Main Menu Setting the functions Main menuFunction Color ADJ Adjusting the color of the imageFunction Adjust the red-subcontrast of printing image RGB Signal SETSignal selecting menu Additional Special print settingSame Photo NML Print Print setting Deep EchoData COMADJ Comment System settingMaking a comment System1USER Size ADJ Setting the image sizeMaking a comment Setting the functions Making a commentMenu display Remote control function on the comment displayEditing command Comment making procedureSelecting comment block Inputting the letterCase of deleting E Close the comment menu Setting Functions Memory SW Menu Setting the functions Memory SW menuChange OK / CANCEL/ Init CancelKEY SET Time ADJ Setting the day and present timeSetting the buttons function ADJ Signal setting display SignalPrint SET Print settingMargin cut LOW RET ReturnHigh Following printing is available Printing procedures Special printsAbcd Printing Procedures Special printsImage prints Multi prints Images Image size and the number of memory pagesMulti Prints Setting the multi-print menu1Displaying the image from input signal source image Storing images in memory Field 1Printing the imagesPhoto Prints Setting Photo print menuSelecting the size Displaying the image from input signal source imagePrinting the images Separate Print1Displaying the source image image from the input signal Setting the multi-print and photo-print menus1Setting the Separate function 1Storing images in memory / Printing the images Selecting Field or Frame Setting Strobe functionStrobe Prints Printing Procedures Special prints 1Storing images in memory Displaying the source image image from the input signal1Interrupting strobe memory SettingtheautomaticintervalprintingPressing the Print button Automatic interval prints 1 image1Interrupting automatic interval prints Pressing the Memory buttonMemory External Remote 2 terminal on the rear panelBusy RemotePin No Remote terminal Circuit inside the VCPExternal Remote 1 terminal on the rear panel Timing ChartTroubleshooting Overcoming paper jams TroubleshootingSymptom Before calling for serviceTroubleshooting K65HM OptionsSpecifications German Branch Mitsubishi Electric Europe B.V UK BranchFrench Branch Italian Branch