Mitsubishi Electronics CP700E operation manual Installing print paper and ink sheet

Page 8

3. Preparations before operation

3Installing print paper and ink sheet

1Installation procedure of print paper

1Move the knob on the printing unit to the direction indicated by the arrow.

2Insert the print paper in the position as shown below. Place the gear to the right side.

Right side	Print paper	Folder	Left side

		Insert

Folder

Print paper

•Set the paper roll first on the right side paper holder.

•Set the paper roll on the left side paper holder.

3Insert the print paper between roller 1 and 2.

4Insert the edge of the print paper to roller 3. Be sure to insert the paper straight.

RollerRoller

Paper

Paper

Roller

Paper

Roller 2

Roller 3

Roller 1

Print paper

INCORRECT CORRECT INCORRECT

5Feed the print paper through the exit slot straight with your hand.

6Pull the print paper to eliminate slack.

7Move the knob on the side of the printing unit to the direction as indicated by the arrow.

7

Image 8

Contents CP700E Contents Precautions Power RequirementPrecautions Be Careful with the Printing UnitSafety Checks Installing the lithium battery Installing the print paper and ink cassetteSetting the present time Remove the fixed screw on the printing unitInstalling the lithium battery Preparations before operationInstalling print paper and ink sheet Installation procedure of print paper1Set the printing unit Install the ink sheetInstall the ink cassette Precautions before printing After printingMenu display Main MenuSetting the present time Setting the day and present timeSetting the present time Change the date and present time setting ChangeConnection with RGB Analog Signal equipment Connection with external equipmentConnection with Monitors Connection with RS-232C equipmentConnection with external equipment Monitor Setting the output sync. signal Output Sync OFFVideo signal Connection with external equipment VIDEO/S-VIDEOVideo VCPConnection with external equipment RGB Analog signal Setting the switchesDisplaying System Set Menu Setting Baud RateDisplaying the menu screen Setting the RS-232C Command Type Connection with external equipment RS-232C InterfaceRS-232C Data Signal Features and functions Front PanelFeatures and Functions Inside of Printing UnitPotential equalization connector Rear PanelRemote Control Color AdjustPrint button Continuous printing Printing procedures Basic printsPrinting Printing Procedures Basic prints PrintingSelecting Field or Frame FIELD/FRAMESelecting input signal Press the SET button Main Menu is displayed 1Setting print size S/L Save PRG Memory Storing images in memory / Printing the images Image memorizing with page INC Page Increment functionSetting the number of prints Cancelling continuous printingContinuous printing E L DChanging the number of prints during printing Setting the functions Setting the functions OperationButton function setting display Main Menu Memory SW menu Displaying menu screen Memory SW Menu sub menu displayDisplaying the sub menu Y L O C KSET Main Menu Setting the functions Main menuFunction Adjusting the color of the image Color ADJFunction Adjust the red-subcontrast of printing image RGB Signal SETSignal selecting menu Special print setting AdditionalSame PhotoPrint Print setting NMLDeep EchoData COMADJ System setting CommentMaking a comment SystemSetting the image size 1USER Size ADJSetting the functions Making a comment Making a commentRemote control function on the comment display Menu displayComment making procedure Editing commandInputting the letter Selecting comment blockCase of deleting E Close the comment menu Setting the functions Memory SW menu Setting Functions Memory SW MenuChange OK / CANCEL/ Init CancelKEY SET Time ADJ Setting the day and present timeSetting the buttons function Signal ADJ Signal setting displayPrint setting Print SETMargin cut LOW RET ReturnHigh Printing procedures Special prints Following printing is availableAbcd Printing Procedures Special printsImage prints Multi prints Image size and the number of memory pages ImagesSetting the multi-print menu Multi Prints1Displaying the image from input signal source image Storing images in memory 1Printing the images FieldSetting Photo print menu Photo PrintsDisplaying the image from input signal source image Selecting the sizeSeparate Print Printing the images1Displaying the source image image from the input signal Setting the multi-print and photo-print menus1Setting the Separate function 1Storing images in memory / Printing the images Selecting Field or Frame Setting Strobe functionStrobe Prints Printing Procedures Special prints Displaying the source image image from the input signal 1Storing images in memorySettingtheautomaticintervalprinting 1Interrupting strobe memoryPressing the Print button Automatic interval prints 1 imagePressing the Memory button 1Interrupting automatic interval printsExternal Remote 2 terminal on the rear panel MemoryBusy RemoteCircuit inside the VCP Pin No Remote terminalTiming Chart External Remote 1 terminal on the rear panelTroubleshooting Troubleshooting Overcoming paper jamsBefore calling for service SymptomTroubleshooting Options K65HMSpecifications Mitsubishi Electric Europe B.V UK Branch German BranchFrench Branch Italian Branch