Mitsubishi Electronics CP700E operation manual Safety Checks

Page 5

2. Precautions

CAUTION ON RELOCATING

When transporting this unit, make sure it is not likely to be subjected to impacts. They can be a prime cause for damage. Further, make sure to disconnect the power cord from the power outlet, and the cables from the connected devices.

SAFETY CHECKS

Periods: According to the recommendations of the manufacturer of the medical device.

Scope: a) Visual inspection

Housing, leads, controls, displays, labels/ markings, accessories, operation manual.

b)Funcitonslity test

Testing of functions (according to operation manual) as well as compatibility and usability of device and accessories.

c)Electrical test

Testing of electrical safety of the system according to EN60601-1.

High humidity or dust

Avoid locations with high humidity and dust in order to avoid malfunctioning of the device.

Also avoid locations subject to corrosive gasses and smoke.

Heat

Direct sunlight, heaters or other heat sources may deform the housing and subsequently cause malfunctioning.

TECHNICAL DESCRIPTIONS

The supplier will make available on request such circuit diagrams, component part lists, descriptions, calibration instructions or other information which will assist the USER's appropriately qualified technical personnel to repair those parts of the EQUIPMENT which are classified by the manufacturer as repairable.

The use of ACCESSORY equipment not complying with the equivalent safety requirements of this equipment may lead to a reduced level of safety of the resulting system.

Consideration relating to the choice shall include:

-use of the accessory in the PATIENT VICINITY

-evidence that the safety certification of the ACCESSORY has been performed in accordance to the appropriate EN60601-1 and/or EN60601-1-1 harmonized national standard.

The transportation and storage environmental conditions are :

Temperature : -20°C - +60°C (-4F°- +140°F)

Humidity : 90%RH or less at 40°C (104°F)

Note : The above transportation environmental conditions indicate the storage environmental conditions during transport.

OTHER CAUTIONS

Dust or other foreign matter adhering to the print paper or the sheet cartridge, or deformation resulting from exposure to extremely low or high temperatures could cause loss of colour, uneven colour or lines, or wrinkles in the print images.

If there is noise or vibration in the VCR still-image or playback picture, the print image may be distorted or the upper part may be crooked.

NOTE:

YOUR UNDERSTANDING IS REQUESTED FOR THE LOSS OF IMAGES IN MEMORY DUE TO THE SUDDEN

OCCURRENCE OF A MALFUNCTION.

As for paper sheet set, refer to page 7 “Installing print paper and ink sheet”.

This product is to be employed with medical equipment, just for reference

purpose, not for medical diagnostic purpose.

4

Page 4 Page 6
Image 5
Page 4 Page 6
Contents CP700E Contents Power Requirement PrecautionsBe Careful with the Printing Unit PrecautionsSafety Checks Installing the print paper and ink cassette Installing the lithium batterySetting the present time Remove the fixed screw on the printing unitPreparations before operation Installing the lithium batteryInstallation procedure of print paper Installing print paper and ink sheet1Set the printing unit Install the ink sheetInstall the ink cassette After printing Precautions before printingMain Menu Menu displaySetting the day and present time Setting the present timeSetting the present time Change Change the date and present time settingConnection with external equipment Connection with RGB Analog Signal equipmentConnection with Monitors Connection with RS-232C equipmentConnection with external equipment Monitor OFF Setting the output sync. signal Output SyncConnection with external equipment VIDEO/S-VIDEO Video signalVideo VCPSetting the switches Connection with external equipment RGB Analog signalDisplaying System Set Menu Setting Baud RateDisplaying the menu screen Connection with external equipment RS-232C Interface Setting the RS-232C Command TypeRS-232C Data Signal Front Panel Features and functionsInside of Printing Unit Features and FunctionsRear Panel Potential equalization connectorColor Adjust Remote ControlPrint button Continuous printing Printing procedures Basic printsPrinting Printing Printing Procedures Basic printsSelecting Field or Frame FIELD/FRAMESelecting input signal Press the SET button Main Menu is displayed 1Setting print size S/L Save PRG Memory Image memorizing with page INC Page Increment function Storing images in memory / Printing the imagesCancelling continuous printing Setting the number of printsContinuous printing E L DChanging the number of prints during printing Setting the functions Operation Setting the functionsButton function setting display Main Menu Memory SW menu Memory SW Menu sub menu display Displaying menu screenDisplaying the sub menu Y L O C KSET Main Menu Setting the functions Main menuFunction Color ADJ Adjusting the color of the imageFunction Adjust the red-subcontrast of printing image RGB Signal SETSignal selecting menu Additional Special print settingSame PhotoNML Print Print settingDeep EchoData COMADJ Comment System settingMaking a comment System1USER Size ADJ Setting the image sizeMaking a comment Setting the functions Making a commentMenu display Remote control function on the comment displayEditing command Comment making procedureSelecting comment block Inputting the letterCase of deleting E Close the comment menu Setting Functions Memory SW Menu Setting the functions Memory SW menuChange OK / CANCEL/ Init CancelKEY SET Time ADJ Setting the day and present timeSetting the buttons function ADJ Signal setting display SignalPrint SET Print settingMargin cut LOW RET ReturnHigh Following printing is available Printing procedures Special printsAbcd Printing Procedures Special printsImage prints Multi prints Images Image size and the number of memory pagesMulti Prints Setting the multi-print menu1Displaying the image from input signal source image Storing images in memory Field 1Printing the imagesPhoto Prints Setting Photo print menuSelecting the size Displaying the image from input signal source imagePrinting the images Separate Print1Displaying the source image image from the input signal Setting the multi-print and photo-print menus1Setting the Separate function 1Storing images in memory / Printing the images Selecting Field or Frame Setting Strobe functionStrobe Prints Printing Procedures Special prints 1Storing images in memory Displaying the source image image from the input signal1Interrupting strobe memory SettingtheautomaticintervalprintingPressing the Print button Automatic interval prints 1 image1Interrupting automatic interval prints Pressing the Memory buttonMemory External Remote 2 terminal on the rear panelBusy RemotePin No Remote terminal Circuit inside the VCPExternal Remote 1 terminal on the rear panel Timing ChartTroubleshooting Overcoming paper jams TroubleshootingSymptom Before calling for serviceTroubleshooting K65HM OptionsSpecifications German Branch Mitsubishi Electric Europe B.V UK BranchFrench Branch Italian Branch
Top Page Image Contents