Mitsubishi Electronics CP700E Preparations before operation, Installing the lithium battery

Page 7

3. Preparations before operation

1Remove the protective cushion.

Note: Unplug the power cord from outlet for safety.

1Press the OPEN button on the front panel. Printing unit will slide out.

Attention}

,Do not touch the thermal head.

Fingerprints or dust on the thermal head will degrade the print quality.

2Pull out the protective cushion from the right side.

Attention}

,Keep the protective cushion for transporting this unit.

,It is very important to transport this printer with the protective cushion installed so as not to damage the printing unit.

Protective cushion

2Installing the lithium battery

Power for memory of day and present time are supplied by a lithium battery.

Install the lithium battery ( accessory CR2025) by the following procedure after plugging the VCP.

{Install the lithium battery to the folder.

Folder

1 Open the door.

2 Install the battery with the (+) side facing out.

3 Close the door.

,If the installed battery is dead or a battery has been installed incorrectly, the built-in clock and power loss listing will not function properly.

,When changing the battery, pry the battery out of the holder with a sharp object.

,After changing the battery, set the present time and day.

Note:

,Take care of the battery. Refer to pages on lithium battery precaution.

,The setting before installing the battery is not valid. When operating this unit without any settings, the strobe function may not be operated.

6

Image 7

Contents CP700E Contents Power Requirement PrecautionsBe Careful with the Printing Unit PrecautionsSafety Checks Remove the fixed screw on the printing unit Installing the lithium batteryInstalling the print paper and ink cassette Setting the present timePreparations before operation Installing the lithium batteryInstallation procedure of print paper Installing print paper and ink sheetInstall the ink cassette Install the ink sheet1Set the printing unit After printing Precautions before printingMain Menu Menu displaySetting the day and present time Setting the present timeSetting the present time Change Change the date and present time settingConnection with RS-232C equipment Connection with RGB Analog Signal equipmentConnection with external equipment Connection with MonitorsConnection with external equipment Monitor OFF Setting the output sync. signal Output SyncVCP Video signalConnection with external equipment VIDEO/S-VIDEO VideoSetting the switches Connection with external equipment RGB Analog signalDisplaying the menu screen Setting Baud RateDisplaying System Set Menu Connection with external equipment RS-232C Interface Setting the RS-232C Command TypeRS-232C Data Signal Front Panel Features and functionsInside of Printing Unit Features and FunctionsRear Panel Potential equalization connectorColor Adjust Remote ControlPrint button Printing Printing procedures Basic printsContinuous printing FIELD/FRAME Printing Procedures Basic printsPrinting Selecting Field or FrameSelecting input signal Press the SET button Main Menu is displayed 1Setting print size S/L Save PRG Memory Image memorizing with page INC Page Increment function Storing images in memory / Printing the imagesE L D Setting the number of printsCancelling continuous printing Continuous printingChanging the number of prints during printing Setting the functions Operation Setting the functionsButton function setting display Main Menu Memory SW menu Y L O C K Displaying menu screenMemory SW Menu sub menu display Displaying the sub menuSET Function Setting the functions Main menuMain Menu Color ADJ Adjusting the color of the imageFunction Adjust the red-subcontrast of printing image Signal selecting menu Signal SETRGB Photo Special print settingAdditional SameEcho Print Print settingNML DeepADJ COMData System System settingComment Making a comment1USER Size ADJ Setting the image sizeMaking a comment Setting the functions Making a commentMenu display Remote control function on the comment displayEditing command Comment making procedureSelecting comment block Inputting the letterCase of deleting E Close the comment menu Cancel Setting the functions Memory SW menuSetting Functions Memory SW Menu Change OK / CANCEL/ InitSetting the buttons function Time ADJ Setting the day and present timeKEY SET ADJ Signal setting display SignalPrint SET Print settingMargin cut High RET ReturnLOW Following printing is available Printing procedures Special printsImage prints Multi prints Printing Procedures Special printsAbcd Images Image size and the number of memory pagesMulti Prints Setting the multi-print menu1Displaying the image from input signal source image Storing images in memory Field 1Printing the imagesPhoto Prints Setting Photo print menuSelecting the size Displaying the image from input signal source imagePrinting the images Separate Print1Setting the Separate function Setting the multi-print and photo-print menus1Displaying the source image image from the input signal Strobe Prints Selecting Field or Frame Setting Strobe function1Storing images in memory / Printing the images Printing Procedures Special prints 1Storing images in memory Displaying the source image image from the input signalAutomatic interval prints 1 image Settingtheautomaticintervalprinting1Interrupting strobe memory Pressing the Print button1Interrupting automatic interval prints Pressing the Memory buttonRemote External Remote 2 terminal on the rear panelMemory BusyPin No Remote terminal Circuit inside the VCPExternal Remote 1 terminal on the rear panel Timing ChartTroubleshooting Overcoming paper jams TroubleshootingSymptom Before calling for serviceTroubleshooting K65HM OptionsSpecifications Italian Branch Mitsubishi Electric Europe B.V UK BranchGerman Branch French Branch