Mitsubishi Electronics CP700E operation manual Circuit inside the VCP, Pin No Remote terminal

Page 83

8. Printing Procedures (Special prints)

1Circuit inside the VCP

}VCP

User side

		DC5V
	DTC124EK	10KΩ
		10KΩ
To VCP	22KΩ	100 Ω 2 MEMORY
	22KΩ
		DC5V
	DTC124EK	2.2KΩ
	22KΩ	100 Ω 4 BUSY
From VCP	22KΩ
		DC5V
	DTC124EK	10KΩ
		10KΩ
To VCP	22KΩ	100 Ω 5 PRINT
	22KΩ
To VCP	1K	6 REMOTE
To VCP		6 REMOTE

Pin No. 6 REMOTE terminal

By sending the following remote control codes from Pin No. 6, the same functions as the wired remote

control (accessory) can be controlled.

Code	Function	Code	Function
01	LEFT SHIFT button	02	RIGHT SHIFT button
03	DOWN SHIFT button	04	UP SHIFT button
08	PRINT Q’ty button (increase)	09
0A*	MENU button	0B*	CLEAR button
0C	PRINT Q’ty button(decrease)	0D
0E*	SET button	0F*	STOP button
12*	PROG. (Program) button	13*	PRINT button
15*	FIELD/FRAME button	16*	COLOR ADJUST button
17*	MEMORY button	18*	DISPLAY button
1C*	MEMORY PAGE button	1D*	MONITOR button

In case of the codes with * mark, 5 words are sent.

82

Image 83

Contents CP700E Contents Power Requirement PrecautionsBe Careful with the Printing Unit PrecautionsSafety Checks Remove the fixed screw on the printing unit Installing the lithium batteryInstalling the print paper and ink cassette Setting the present timePreparations before operation Installing the lithium batteryInstallation procedure of print paper Installing print paper and ink sheet1Set the printing unit Install the ink sheetInstall the ink cassette After printing Precautions before printingMain Menu Menu displaySetting the day and present time Setting the present timeSetting the present time Change Change the date and present time settingConnection with RS-232C equipment Connection with RGB Analog Signal equipmentConnection with external equipment Connection with MonitorsConnection with external equipment Monitor OFF Setting the output sync. signal Output SyncVCP Video signalConnection with external equipment VIDEO/S-VIDEO VideoSetting the switches Connection with external equipment RGB Analog signalDisplaying System Set Menu Setting Baud RateDisplaying the menu screen Connection with external equipment RS-232C Interface Setting the RS-232C Command TypeRS-232C Data Signal Front Panel Features and functionsInside of Printing Unit Features and FunctionsRear Panel Potential equalization connectorColor Adjust Remote ControlPrint button Continuous printing Printing procedures Basic printsPrinting FIELD/FRAME Printing Procedures Basic printsPrinting Selecting Field or FrameSelecting input signal Press the SET button Main Menu is displayed 1Setting print size S/L Save PRG Memory Image memorizing with page INC Page Increment function Storing images in memory / Printing the imagesE L D Setting the number of printsCancelling continuous printing Continuous printingChanging the number of prints during printing Setting the functions Operation Setting the functionsButton function setting display Main Menu Memory SW menu Y L O C K Displaying menu screenMemory SW Menu sub menu display Displaying the sub menuSET Main Menu Setting the functions Main menuFunction Color ADJ Adjusting the color of the imageFunction Adjust the red-subcontrast of printing image RGB Signal SETSignal selecting menu Photo Special print settingAdditional SameEcho Print Print settingNML DeepData COMADJ System System settingComment Making a comment1USER Size ADJ Setting the image sizeMaking a comment Setting the functions Making a commentMenu display Remote control function on the comment displayEditing command Comment making procedureSelecting comment block Inputting the letterCase of deleting E Close the comment menu Cancel Setting the functions Memory SW menuSetting Functions Memory SW Menu Change OK / CANCEL/ InitKEY SET Time ADJ Setting the day and present timeSetting the buttons function ADJ Signal setting display SignalPrint SET Print settingMargin cut LOW RET ReturnHigh Following printing is available Printing procedures Special printsAbcd Printing Procedures Special printsImage prints Multi prints Images Image size and the number of memory pagesMulti Prints Setting the multi-print menu1Displaying the image from input signal source image Storing images in memory Field 1Printing the imagesPhoto Prints Setting Photo print menuSelecting the size Displaying the image from input signal source imagePrinting the images Separate Print1Displaying the source image image from the input signal Setting the multi-print and photo-print menus1Setting the Separate function 1Storing images in memory / Printing the images Selecting Field or Frame Setting Strobe functionStrobe Prints Printing Procedures Special prints 1Storing images in memory Displaying the source image image from the input signalAutomatic interval prints 1 image Settingtheautomaticintervalprinting1Interrupting strobe memory Pressing the Print button1Interrupting automatic interval prints Pressing the Memory buttonRemote External Remote 2 terminal on the rear panelMemory BusyPin No Remote terminal Circuit inside the VCPExternal Remote 1 terminal on the rear panel Timing ChartTroubleshooting Overcoming paper jams TroubleshootingSymptom Before calling for serviceTroubleshooting K65HM OptionsSpecifications Italian Branch Mitsubishi Electric Europe B.V UK BranchGerman Branch French Branch