Mitsubishi Electronics CP700E operation manual Troubleshooting

Page 88

9. Troubleshooting

Symptom

1The stored image in the memory cannot be enlarged to fill the maximum print area.

1The color or picture quality is different between the memorized image and the printed image.

1The image on the monitor screen printed paper is not colored correctly.

(When the VIDEO signal without color burst signal is inputted to the unit, the image on the monitor screen or printed image becomes monochrome or rainbow-like colored image.)

1The color or picture quality is different between the image on the monitor screen and the printed image. (When the color and picture quality are same between the image stored in the memory and the printed image.)

1The set comments do not appear on the print paper.

1Wired remote control cannot be operated.

Check and Remedy

Is the SMALL size ink-sheet installed when selecting “S” in “MODE : S/L”?

Or is the LARGE size ink-sheet installed when selecting “L” in “MODE : S/L”?

→Check the current setting. Refer to pages 31 - 32.

Is the paper size set to “N” in the size setting in SYSTEM menu?

→Set the size to “M” or “W”. Refer to page 51.

Is the S size image printed on the L size paper?

→Check the current setting. Refer to pages 31 - 32.

Is the print area set correctly in the USER SIZE ADJ?

→Check the setting of the print area. Refer to pages 52 - 53.

Is the color of the image stored in the memory adjusted?

→Adjust the color of the image stored in the memory with the image adjustment display (COLOR ADJ). Refer to pages 45 -46.

Is the DCF set to “OFF”?

→Set the DCF to “OFF”. Refer to page 47.

Is the image on the monitor screen adjusted?

→Adjust the image on the monitor screen with “MON R-SUB” and “MON B-SUB” in the SIGNAL ADJ menu in the signal setting display. Refer to page 62.

Is the COMMENT set to “OFF”?

→Set the COMMENT to “COM”. Refer to page 50. Is the COMMENT inputted?

→Input the COMMENT on the menu. Refer to page 56.

Is the plug of the remote control disconnected from its terminal on the unit?

→Connect the plug of the remote control to the REMOTE terminal on the unit.

Is the wired remote control for this unit (accessory) used?

→Use the remote control for this unit.

Is this unit operated through RS-232C interface?

→Set “KEY MASK” to “OFF” through RS-232C interface.

87

Image 88

Contents CP700E Contents Precautions Power RequirementPrecautions Be Careful with the Printing UnitSafety Checks Installing the lithium battery Installing the print paper and ink cassetteSetting the present time Remove the fixed screw on the printing unitInstalling the lithium battery Preparations before operationInstalling print paper and ink sheet Installation procedure of print paperInstall the ink cassette Install the ink sheet1Set the printing unit Precautions before printing After printingMenu display Main MenuSetting the present time Setting the day and present timeSetting the present time Change the date and present time setting ChangeConnection with RGB Analog Signal equipment Connection with external equipmentConnection with Monitors Connection with RS-232C equipmentConnection with external equipment Monitor Setting the output sync. signal Output Sync OFFVideo signal Connection with external equipment VIDEO/S-VIDEOVideo VCPConnection with external equipment RGB Analog signal Setting the switchesDisplaying the menu screen Setting Baud RateDisplaying System Set Menu Setting the RS-232C Command Type Connection with external equipment RS-232C InterfaceRS-232C Data Signal Features and functions Front PanelFeatures and Functions Inside of Printing UnitPotential equalization connector Rear PanelRemote Control Color AdjustPrint button Printing Printing procedures Basic printsContinuous printing Printing Procedures Basic prints PrintingSelecting Field or Frame FIELD/FRAMESelecting input signal Press the SET button Main Menu is displayed 1Setting print size S/L Save PRG Memory Storing images in memory / Printing the images Image memorizing with page INC Page Increment functionSetting the number of prints Cancelling continuous printingContinuous printing E L DChanging the number of prints during printing Setting the functions Setting the functions OperationButton function setting display Main Menu Memory SW menu Displaying menu screen Memory SW Menu sub menu displayDisplaying the sub menu Y L O C KSET Function Setting the functions Main menuMain Menu Adjusting the color of the image Color ADJFunction Adjust the red-subcontrast of printing image Signal selecting menu Signal SETRGB Special print setting AdditionalSame PhotoPrint Print setting NMLDeep EchoADJ COMData System setting CommentMaking a comment SystemSetting the image size 1USER Size ADJSetting the functions Making a comment Making a commentRemote control function on the comment display Menu displayComment making procedure Editing commandInputting the letter Selecting comment blockCase of deleting E Close the comment menu Setting the functions Memory SW menu Setting Functions Memory SW MenuChange OK / CANCEL/ Init CancelSetting the buttons function Time ADJ Setting the day and present timeKEY SET Signal ADJ Signal setting displayPrint setting Print SETMargin cut High RET ReturnLOW Printing procedures Special prints Following printing is availableImage prints Multi prints Printing Procedures Special printsAbcd Image size and the number of memory pages ImagesSetting the multi-print menu Multi Prints1Displaying the image from input signal source image Storing images in memory 1Printing the images FieldSetting Photo print menu Photo PrintsDisplaying the image from input signal source image Selecting the sizeSeparate Print Printing the images1Setting the Separate function Setting the multi-print and photo-print menus1Displaying the source image image from the input signal Strobe Prints Selecting Field or Frame Setting Strobe function1Storing images in memory / Printing the images Printing Procedures Special prints Displaying the source image image from the input signal 1Storing images in memorySettingtheautomaticintervalprinting 1Interrupting strobe memoryPressing the Print button Automatic interval prints 1 imagePressing the Memory button 1Interrupting automatic interval printsExternal Remote 2 terminal on the rear panel MemoryBusy RemoteCircuit inside the VCP Pin No Remote terminalTiming Chart External Remote 1 terminal on the rear panelTroubleshooting Troubleshooting Overcoming paper jamsBefore calling for service SymptomTroubleshooting Options K65HMSpecifications Mitsubishi Electric Europe B.V UK Branch German BranchFrench Branch Italian Branch