Mitsubishi Electronics CP700E operation manual RET Return, High, Low

Page 65

7. Setting the functions (Memory SW menu)

5 SYSTEM

System setting 2

PRG ALL INIT ( Program All Initial )

All settings of 3 memory programs to store each function is initialized.

ON	Each setting function is initialized
OFF	Not initialized

This function is available when selecting “OK” in the “CHANGE : OK/ CANCEL/INIT” of “MEMORY

SW MENU” and pressing the SET button.

Once this function is set to “ON” and the source image is displayed,the setting is initialized and the image stored in the memory is cleared even if this function is set to “OFF”.

BAUD RATE

Function Setting the Baud Rate according to connected equipment. Refer to pages 19-21 .

COMMAND TYPE

Function Setting the RS-232C command type.

Select “A” or “B” according to connected equipment.

Normally, set the “COMMAND TYPE” to “A”. Refer to page 20.

RESPONSE

Function Select the RS-232C response from the unit to be sent back or not to the host computer. Select “RET(return)” or “NO” .

RET (RETURN)	The RS-232C response is sent back to the host computer.
NO	The RS-232C response is not sent back to the host computer.

REMOTE BUSY

Function Setting the BUSY signal of remote terminal (REMOTE 1/ REMOTE 2) on the rear panel. Normally, set the “REMOTE BUSY” to “H”.

Select “H” or “L” according to connected equipment. Refer to page 20.

H (HIGH)	The VCP cannot accept the remote input signal when the signal is “HIGH”.
L (LOW)	The VCP cannot accept the remote input signal when the signal is “LOW”.

REMAINING

Function Inform the number of remaining paper by a buzzer tone.

OFF	This function is not available.
0	The buzzer sounds five times as the point you set.
	The setting area is 0 to 10.

Please observe the following precautions when you use this function.

•If a paper jam occurs, the remaining paper may not be informed correctly.

•Do not change the ink sheet size S to L ( or L to S) in the middle of using ink sheet.

•Make sure to replace the print paper and ink sheet at the same time.

•Make sure to use the new one when you set the ink sheet and print paper.

•Do not feed the print paper after you set the print paper.

64

Image 65

Contents CP700E Contents Power Requirement PrecautionsBe Careful with the Printing Unit PrecautionsSafety Checks Installing the print paper and ink cassette Installing the lithium batterySetting the present time Remove the fixed screw on the printing unitPreparations before operation Installing the lithium batteryInstallation procedure of print paper Installing print paper and ink sheet1Set the printing unit Install the ink sheetInstall the ink cassette After printing Precautions before printingMain Menu Menu displaySetting the day and present time Setting the present timeSetting the present time Change Change the date and present time settingConnection with external equipment Connection with RGB Analog Signal equipmentConnection with Monitors Connection with RS-232C equipmentConnection with external equipment Monitor OFF Setting the output sync. signal Output SyncConnection with external equipment VIDEO/S-VIDEO Video signalVideo VCPSetting the switches Connection with external equipment RGB Analog signalDisplaying System Set Menu Setting Baud RateDisplaying the menu screen Connection with external equipment RS-232C Interface Setting the RS-232C Command TypeRS-232C Data Signal Front Panel Features and functionsInside of Printing Unit Features and FunctionsRear Panel Potential equalization connectorColor Adjust Remote ControlPrint button Continuous printing Printing procedures Basic printsPrinting Printing Printing Procedures Basic printsSelecting Field or Frame FIELD/FRAMESelecting input signal Press the SET button Main Menu is displayed 1Setting print size S/L Save PRG Memory Image memorizing with page INC Page Increment function Storing images in memory / Printing the imagesCancelling continuous printing Setting the number of printsContinuous printing E L DChanging the number of prints during printing Setting the functions Operation Setting the functionsButton function setting display Main Menu Memory SW menu Memory SW Menu sub menu display Displaying menu screenDisplaying the sub menu Y L O C KSET Main Menu Setting the functions Main menuFunction Color ADJ Adjusting the color of the imageFunction Adjust the red-subcontrast of printing image RGB Signal SETSignal selecting menu Additional Special print settingSame PhotoNML Print Print settingDeep EchoData COMADJ Comment System settingMaking a comment System1USER Size ADJ Setting the image sizeMaking a comment Setting the functions Making a commentMenu display Remote control function on the comment displayEditing command Comment making procedureSelecting comment block Inputting the letterCase of deleting E Close the comment menu Setting Functions Memory SW Menu Setting the functions Memory SW menuChange OK / CANCEL/ Init CancelKEY SET Time ADJ Setting the day and present timeSetting the buttons function ADJ Signal setting display SignalPrint SET Print settingMargin cut LOW RET ReturnHigh Following printing is available Printing procedures Special printsAbcd Printing Procedures Special printsImage prints Multi prints Images Image size and the number of memory pagesMulti Prints Setting the multi-print menu1Displaying the image from input signal source image Storing images in memory Field 1Printing the imagesPhoto Prints Setting Photo print menuSelecting the size Displaying the image from input signal source imagePrinting the images Separate Print1Displaying the source image image from the input signal Setting the multi-print and photo-print menus1Setting the Separate function 1Storing images in memory / Printing the images Selecting Field or Frame Setting Strobe functionStrobe Prints Printing Procedures Special prints 1Storing images in memory Displaying the source image image from the input signal1Interrupting strobe memory SettingtheautomaticintervalprintingPressing the Print button Automatic interval prints 1 image1Interrupting automatic interval prints Pressing the Memory buttonMemory External Remote 2 terminal on the rear panelBusy RemotePin No Remote terminal Circuit inside the VCPExternal Remote 1 terminal on the rear panel Timing ChartTroubleshooting Overcoming paper jams TroubleshootingSymptom Before calling for serviceTroubleshooting K65HM OptionsSpecifications German Branch Mitsubishi Electric Europe B.V UK BranchFrench Branch Italian Branch