Mitsubishi Electronics CP700E External Remote 2 terminal on the rear panel, Memory, Busy, DC3V

Page 82

8. Printing Procedures (Special prints)

External REMOTE 2 terminal on the rear panel

The images can be stored in memory and printed by sending the remote signal through the external remote terminal on the rear panel.

, Make out the necessary circuit to use this function by referring to the following.

Pin No.

1External remote terminal Signal allocation Connector MINI DIN8PIN

Pin No.	Function	Description
1	Ground	Earth
2	MEMORY	Memory: When the signal becomes “LOW” from “HIGH”, the image is stored in
		memory. (When the signal has been “LOW” for 60msec. or more, the image is
		stored in memory. )

3Unused

4	BUSY	“HIGH” : The VCP cannot accept the remote signal.
		“LOW” : The VCP can accept the remote signal.
		The signal becomes “HIGH” in the following cases;
		(1)	During initialization after the VCP has been switched on
		(2)	For about 1 sec. after the INPUT SELECT switch has been set
		(3)	During displaying the menu screen
		(4)	When the image cannot be stored in memory

5	PRINT	PRINT :When the signal becomes “LOW” from “HIGH”, the image stored in
		the memory is printed. (When the signal has been “LOW” for 60 msec. or
		more, the image is printed.)

6	REMOTE	The same functions as the remote control can be controlled.∗
7	Unused
8	DC3V	Power supply for the remote control DC 1mA MAX
		∗Refer to page 82 for this function.

,When the signal from BUSY terminal is received with TTL level, keep the following. 1 OL =2mA or less, 1 OH =1mA or less

1 OL shows the current flowing into the unit at Low output, 1 OH shows the current flowing out of the unit at High output.

81

Image 82

Contents CP700E Contents Precautions Power RequirementPrecautions Be Careful with the Printing UnitSafety Checks Setting the present time Installing the lithium batteryInstalling the print paper and ink cassette Remove the fixed screw on the printing unitInstalling the lithium battery Preparations before operationInstalling print paper and ink sheet Installation procedure of print paperInstall the ink cassette Install the ink sheet1Set the printing unit Precautions before printing After printingMenu display Main MenuSetting the present time Setting the day and present timeSetting the present time Change the date and present time setting ChangeConnection with Monitors Connection with RGB Analog Signal equipmentConnection with external equipment Connection with RS-232C equipmentConnection with external equipment Monitor Setting the output sync. signal Output Sync OFFVideo Video signalConnection with external equipment VIDEO/S-VIDEO VCPConnection with external equipment RGB Analog signal Setting the switchesDisplaying the menu screen Setting Baud RateDisplaying System Set Menu Setting the RS-232C Command Type Connection with external equipment RS-232C InterfaceRS-232C Data Signal Features and functions Front PanelFeatures and Functions Inside of Printing UnitPotential equalization connector Rear PanelRemote Control Color AdjustPrint button Printing Printing procedures Basic printsContinuous printing Selecting Field or Frame Printing Procedures Basic printsPrinting FIELD/FRAMESelecting input signal Press the SET button Main Menu is displayed 1Setting print size S/L Save PRG Memory Storing images in memory / Printing the images Image memorizing with page INC Page Increment functionContinuous printing Setting the number of printsCancelling continuous printing E L DChanging the number of prints during printing Setting the functions Setting the functions OperationButton function setting display Main Menu Memory SW menu Displaying the sub menu Displaying menu screenMemory SW Menu sub menu display Y L O C KSET Function Setting the functions Main menuMain Menu Adjusting the color of the image Color ADJFunction Adjust the red-subcontrast of printing image Signal selecting menu Signal SETRGB Same Special print settingAdditional PhotoDeep Print Print settingNML EchoADJ COMData Making a comment System settingComment SystemSetting the image size 1USER Size ADJSetting the functions Making a comment Making a commentRemote control function on the comment display Menu displayComment making procedure Editing commandInputting the letter Selecting comment blockCase of deleting E Close the comment menu Change OK / CANCEL/ Init Setting the functions Memory SW menuSetting Functions Memory SW Menu CancelSetting the buttons function Time ADJ Setting the day and present timeKEY SET Signal ADJ Signal setting displayPrint setting Print SETMargin cut High RET ReturnLOW Printing procedures Special prints Following printing is availableImage prints Multi prints Printing Procedures Special printsAbcd Image size and the number of memory pages ImagesSetting the multi-print menu Multi Prints1Displaying the image from input signal source image Storing images in memory 1Printing the images FieldSetting Photo print menu Photo PrintsDisplaying the image from input signal source image Selecting the sizeSeparate Print Printing the images1Setting the Separate function Setting the multi-print and photo-print menus1Displaying the source image image from the input signal Strobe Prints Selecting Field or Frame Setting Strobe function1Storing images in memory / Printing the images Printing Procedures Special prints Displaying the source image image from the input signal 1Storing images in memoryPressing the Print button Settingtheautomaticintervalprinting1Interrupting strobe memory Automatic interval prints 1 imagePressing the Memory button 1Interrupting automatic interval printsBusy External Remote 2 terminal on the rear panelMemory RemoteCircuit inside the VCP Pin No Remote terminalTiming Chart External Remote 1 terminal on the rear panelTroubleshooting Troubleshooting Overcoming paper jamsBefore calling for service SymptomTroubleshooting Options K65HMSpecifications French Branch Mitsubishi Electric Europe B.V UK BranchGerman Branch Italian Branch