Mitsubishi Electronics CP700E operation manual Troubleshooting, Overcoming paper jams

Page 86

9. Troubleshooting

Other messages

	MECHA INITIALIZE REQUEST	Indicated when the power is turned on after turning off during printing.
		Press the MEMORY button for more than one second while pressing
		the MONITOR button.	*Note : 3

	MECHA INITIALIZE	Indicated during initializing.

	PRINT STOP	In the case of pressing the STOP button on the remote control during
	PRINT STOP	printing, this unit is initialized. This message is indicated during initializing.

*Note : 3 This is an operation for initialization. Make sure to press the MONITOR button first. If the MEMORY button is pressed first, a new image will be stored in memory erasing any previously stored image.

1Overcoming paper jams

1 Press the OPEN button to pull out the printing unit.

2Remove the ink cassette.

3Turn the knob on the right side of the printing unit clockwise.

, Roll up the print paper completely.

4Remove the print paper.

5Cut the defective part of print paper with scissors.

6Cut both edges of the print paper.

7Install the print paper. ( Refer to pages 7 - 8.)

85

Image 86

Contents CP700E Contents Precautions Power RequirementPrecautions Be Careful with the Printing UnitSafety Checks Setting the present time Installing the lithium batteryInstalling the print paper and ink cassette Remove the fixed screw on the printing unitInstalling the lithium battery Preparations before operationInstalling print paper and ink sheet Installation procedure of print paper1Set the printing unit Install the ink sheetInstall the ink cassette Precautions before printing After printingMenu display Main MenuSetting the present time Setting the day and present timeSetting the present time Change the date and present time setting ChangeConnection with Monitors Connection with RGB Analog Signal equipmentConnection with external equipment Connection with RS-232C equipmentConnection with external equipment Monitor Setting the output sync. signal Output Sync OFFVideo Video signalConnection with external equipment VIDEO/S-VIDEO VCPConnection with external equipment RGB Analog signal Setting the switchesDisplaying System Set Menu Setting Baud RateDisplaying the menu screen Setting the RS-232C Command Type Connection with external equipment RS-232C InterfaceRS-232C Data Signal Features and functions Front PanelFeatures and Functions Inside of Printing UnitPotential equalization connector Rear PanelRemote Control Color AdjustPrint button Continuous printing Printing procedures Basic printsPrinting Selecting Field or Frame Printing Procedures Basic printsPrinting FIELD/FRAMESelecting input signal Press the SET button Main Menu is displayed 1Setting print size S/L Save PRG Memory Storing images in memory / Printing the images Image memorizing with page INC Page Increment functionContinuous printing Setting the number of printsCancelling continuous printing E L DChanging the number of prints during printing Setting the functions Setting the functions OperationButton function setting display Main Menu Memory SW menu Displaying the sub menu Displaying menu screenMemory SW Menu sub menu display Y L O C KSET Main Menu Setting the functions Main menuFunction Adjusting the color of the image Color ADJFunction Adjust the red-subcontrast of printing image RGB Signal SETSignal selecting menu Same Special print settingAdditional PhotoDeep Print Print settingNML EchoData COMADJ Making a comment System settingComment SystemSetting the image size 1USER Size ADJSetting the functions Making a comment Making a commentRemote control function on the comment display Menu displayComment making procedure Editing commandInputting the letter Selecting comment blockCase of deleting E Close the comment menu Change OK / CANCEL/ Init Setting the functions Memory SW menuSetting Functions Memory SW Menu CancelKEY SET Time ADJ Setting the day and present timeSetting the buttons function Signal ADJ Signal setting displayPrint setting Print SETMargin cut LOW RET ReturnHigh Printing procedures Special prints Following printing is availableAbcd Printing Procedures Special printsImage prints Multi prints Image size and the number of memory pages ImagesSetting the multi-print menu Multi Prints1Displaying the image from input signal source image Storing images in memory 1Printing the images FieldSetting Photo print menu Photo PrintsDisplaying the image from input signal source image Selecting the sizeSeparate Print Printing the images1Displaying the source image image from the input signal Setting the multi-print and photo-print menus1Setting the Separate function 1Storing images in memory / Printing the images Selecting Field or Frame Setting Strobe functionStrobe Prints Printing Procedures Special prints Displaying the source image image from the input signal 1Storing images in memoryPressing the Print button Settingtheautomaticintervalprinting1Interrupting strobe memory Automatic interval prints 1 imagePressing the Memory button 1Interrupting automatic interval printsBusy External Remote 2 terminal on the rear panelMemory RemoteCircuit inside the VCP Pin No Remote terminalTiming Chart External Remote 1 terminal on the rear panelTroubleshooting Troubleshooting Overcoming paper jamsBefore calling for service SymptomTroubleshooting Options K65HMSpecifications French Branch Mitsubishi Electric Europe B.V UK BranchGerman Branch Italian Branch