Mitsubishi Electronics CP700E operation manual Signal SET, Signal selecting menu, Rgb

Page 48

7. Setting the functions (Main menu)

2 SIGNAL SET

Signal selecting menu

INPUT

 

Function Select the signal from inputting signal on the rear panel.

VIDEO

Signal from VIDEO input terminal

S -VIDEO

Signal from S-VIDEO input terminal

RGB

Signal from RGB input terminal

FIELD

Function The odd even field lines will be reversed depending on the input interlaced signal.

Printing image is not clear so that the odd and even field lines may be reversed depending on the input

interlaced signal. In this case, FIELD is set to “REV” .

The image status cannot be checked on the monitor display.

NML (Normal) ....

Not reversed

REV( Reverse ) ..

Reversed the field lines.

A F C

Function Automatic frequency control

This function is to automatically correct the image of a weak signal or in VCR special playback . If the

image is not printed correctly because of a weak TV signal, set the AFC function to “ON”.

,The image distortion on the top may occur when the VCR image is input in pause, field-by-field playback, or FF playback mode. In this case, AFC function is set to “OFF” .

ON

AFC available

OFF

AFC invalid

{This function menu is not displayed and invalid when selecting “FRONT” on “3 .SIGNAL ADJ H-START : NML/FRONT” in MEMORY SW menu.

A G C

Function Automatic gain control (Making the image brighter and stressing the contrast.)

This function is to automatically adjust a dark picture in brightness and prints with sharp contrast. Peak

level of an input signal is detected and signals width is standardized to the appropriate value.

ON

AGC is available

OFF

AGC is invalid

{This function is not displayed when selecting RGB signal.

D C F

Function Select whether separating the composite video signal or not.

When inputting the monochrome signal, this function is set to OFF.

This function is for high quality of monochrome image so that input signal is not though DCF circuit.

When inputting the color signal, this function is set to “ON” . Input signal is through DCF circuit and

the composite video signal is separated.

ON

when inputting color signal

OFF

when inputting monochrome signal

{This function is invalid in RGB or S-VIDEO input signal.

Note: When “DCF” is set to “OFF”, the letter may not be colored on the monitor display.

47

Image 48
Contents CP700E Contents Precautions Power RequirementPrecautions Be Careful with the Printing UnitSafety Checks Installing the lithium battery Installing the print paper and ink cassetteSetting the present time Remove the fixed screw on the printing unitInstalling the lithium battery Preparations before operationInstalling print paper and ink sheet Installation procedure of print paperInstall the ink sheet Install the ink cassette1Set the printing unit Precautions before printing After printingMenu display Main MenuSetting the present time Setting the day and present timeSetting the present time Change the date and present time setting ChangeConnection with RGB Analog Signal equipment Connection with external equipmentConnection with Monitors Connection with RS-232C equipmentConnection with external equipment Monitor Setting the output sync. signal Output Sync OFFVideo signal Connection with external equipment VIDEO/S-VIDEOVideo VCPConnection with external equipment RGB Analog signal Setting the switchesSetting Baud Rate Displaying the menu screenDisplaying System Set Menu Setting the RS-232C Command Type Connection with external equipment RS-232C InterfaceRS-232C Data Signal Features and functions Front PanelFeatures and Functions Inside of Printing UnitPotential equalization connector Rear PanelRemote Control Color AdjustPrint button Printing procedures Basic prints PrintingContinuous printing Printing Procedures Basic prints PrintingSelecting Field or Frame FIELD/FRAMESelecting input signal Press the SET button Main Menu is displayed 1Setting print size S/L Save PRG Memory Storing images in memory / Printing the images Image memorizing with page INC Page Increment functionSetting the number of prints Cancelling continuous printingContinuous printing E L DChanging the number of prints during printing Setting the functions Setting the functions OperationButton function setting display Main Menu Memory SW menu Displaying menu screen Memory SW Menu sub menu displayDisplaying the sub menu Y L O C KSET Setting the functions Main menu FunctionMain Menu Adjusting the color of the image Color ADJFunction Adjust the red-subcontrast of printing image Signal SET Signal selecting menuRGB Special print setting AdditionalSame PhotoPrint Print setting NMLDeep EchoCOM ADJData System setting CommentMaking a comment SystemSetting the image size 1USER Size ADJSetting the functions Making a comment Making a commentRemote control function on the comment display Menu displayComment making procedure Editing commandInputting the letter Selecting comment blockCase of deleting E Close the comment menu Setting the functions Memory SW menu Setting Functions Memory SW MenuChange OK / CANCEL/ Init CancelTime ADJ Setting the day and present time Setting the buttons functionKEY SET Signal ADJ Signal setting displayPrint setting Print SETMargin cut RET Return HighLOW Printing procedures Special prints Following printing is availablePrinting Procedures Special prints Image prints Multi printsAbcd Image size and the number of memory pages ImagesSetting the multi-print menu Multi Prints1Displaying the image from input signal source image Storing images in memory 1Printing the images FieldSetting Photo print menu Photo PrintsDisplaying the image from input signal source image Selecting the sizeSeparate Print Printing the imagesSetting the multi-print and photo-print menus 1Setting the Separate function1Displaying the source image image from the input signal Selecting Field or Frame Setting Strobe function Strobe Prints1Storing images in memory / Printing the images Printing Procedures Special prints Displaying the source image image from the input signal 1Storing images in memorySettingtheautomaticintervalprinting 1Interrupting strobe memoryPressing the Print button Automatic interval prints 1 imagePressing the Memory button 1Interrupting automatic interval printsExternal Remote 2 terminal on the rear panel MemoryBusy RemoteCircuit inside the VCP Pin No Remote terminalTiming Chart External Remote 1 terminal on the rear panelTroubleshooting Troubleshooting Overcoming paper jamsBefore calling for service SymptomTroubleshooting Options K65HMSpecifications Mitsubishi Electric Europe B.V UK Branch German BranchFrench Branch Italian Branch