JVC LPT1100-001A manual Input Setting, Sat S-Video, Input Video / S-VIDEO Video, Avideob

Start playback slightly before the actual point from where you wish to start dubbing.

Perform steps 1 and 2 of AL-1 Output And L-1 Input SettingB (A pg. 63).

Press selection keys to select AF-1 INPUTB, then press

ENTER.

64 EN EDITING

SAT S-VIDEO:		Digital Audio Dubbing
If a connected satellite receiver’s output is compatible with Y/C
signals, set to ASAT S-VIDEOB. (For connection, be sure to use
	You can dub selected audio from a DVD or Audio CD disc to a
a 21-pin SCART cable that is compatible with the Y/C signal.)
DECODER:	digital audio device.
	However, it is not possible to dub copy-protected discs.
To use a decoder connected to the [L-2 IN/DECODER]
connector.
	● Turn on the TV and select the AV mode.
NOTES:
	● Slide the TV/CABLE/SAT/DVD switch to DVD.
● If you have a satellite receiver or a decoder connected to the [L-2
IN/DECODER] connector, be sure to set AL-2 SELECTB back to	Example: Dubbing to an MD
appropriate mode after editing.
● If you are not connecting a satellite receiver or a decoder to the				Recorder
[L-2 IN/DECODER] connector, leave AL-2SELECTB set to
AVIDEOB.
● When AL-2 SELECTB is set to ASAT VIDEOB and ASAT S-VIDEOB,
ASATB appears on the TV screen or front display panel instead of
AL-2B.
● If AL-1 OUTPUTB is set to ASCART S-VIDEOB, it is not possible to
set AL-2 SELECTB to ADECODERB or ASAT VIDEOB.
● If AL-1 OUTPUTB is set to ASCART RGBB, it is not possible to set			Digital audio device
AL-2 SELECTB to ADECODERB or ASAT S-VIDEOB.			(MD deck, etc.)
● If AL-1 OUTPUTB is set to ACOMPONENTB and AL-2 SELECTB to
ASAT VIDEOB, ASAT S-VIDEOB or ADECODERB, be sure to
connect the [L-1 IN/OUT] connector with a TV.			Coaxial cable		Optical cable
● If AL-2 SELECTB is set to ASAT S-VIDEOB, be sure to set AL-1
			(not supplied)		(not supplied)
OUTPUTB to ASCART S-VIDEOB.
● The S-Video output does not support the satellite receiver
function. Make use of the L-1 output when viewing images from			To [DIGITAL AUDIO		To [DIGITAL AUDIO
the satellite receiver.			OUT (COAXIAL)]		OUT (OPTICAL)]

Player

F-1 Input Setting

Set AF-1 INPUTB to the appropriate mode depending on the connector (VIDEO or S-VIDEO) being used on the front panel.

1

2

3Press selection keys to select the appropriate setting, then press ENTER.

4Press SET UP to complete the setting.

DVD VIDEO SET UP				HDD/DVD/DV SET UP	FUNCTION SET UP			INITIAL SET UP
	REC/PLAY SET UP			DISPLAY SET	VIDEO IN/OUT
		MONITOR TYPE				4:3LB
		F-1 INPUT
							VIDEO VIDEO
		L-1 OUTPUT					VIDEOS-VIDEO
		L-1 INPUT				SCART VIDEO
		L-2 SELECT				VIDEO
	SET UP		ENTER SELECT WITH @ THEN PRESS [ENTER]
	EXIT			PRESS [SET UP] TO EXIT
			SELECT

Rear of unit

Note for connection:

Remove the protection cap from the optical cable.

1	Connect the unit and a digital audio device using either an
2	optional optical cable or an optional coaxial cable.
	Place a disc on the unit and load an MD on the connected

* The boldface settings below indicate the settings at your purchase.

8F-1 INPUT ^ VIDEO / S-VIDEO VIDEO:

digital audio device.

3 Select the audio to be dubbed.

4

When connecting an appliance to the [VIDEO] input connector, set to AVIDEOB.

S-VIDEO:

When connecting an appliance to the [S-VIDEO] input connector, set to AS-VIDEOB.

5Press W to pause playback.

6Select the input mode on the connected digital audio device.

7Press I to start playback on the unit.

8Start recording on the digital audio device.

9Stop recording on the digital audio device. Then press o to stop playback on the unit.

NOTE:

There may be a discrepancy of several seconds between where you intend editing to start, and where it actually starts.