JVC VR601 Hard-Disk Drive Installation, System Information, Ide, Quality Best Ntsc Rate 6 HR

Page 10

3.2 Hard-Disk Drive Installation

The DVR is equipped with two compartments of hard-disk drive. The unit usually comes with one hard-disk drive installed in the compartment HD1, which is default-configured as a master. If you need a second hard-disk drive to be installed in the compartment HD2 (Mobile), please contact your distributors or installers for specific instructions on how to install it. Please don’t serve yourself before consulting your installers. If there is only one hard-disk drive in the mobile compartment, please set the HD2 USAGE option to REC (Please refer to section 5.5) before proceed recording function. The jumper-settings arrangement of installed hard-disk drives for the system (Table 3.2 A.) is shown in the tables below.

Table 3.2 A. The jumper settings of hard-disk drives in the system

 

Location

 

Jumper

IDE 1

Compartment HD 1

 

Master (Default)

IDE 2

Compartment HD 2

 

Master

 

 

 

 

Table 3.2 B. Compatible hard-disk drives

 

 

 

 

 

 

 

Manufacturer

Model

Capacity

Rotation

 

3.3 System Information

You can display system settings information as shown on Table 3.3 A below at any time by pressing the Display button . In the playback mode, the recorded video information is displayed. In the live or recording mode, the Manual Recording information is displayed. However, when the DVR is displaying a decoded image from a multiplexer, you must first switch the unit to encoded image displaying (The

pictures is switching swiftly and the light of Monitor button is off) by pressing the Monitor button

. Each sequential press of the Display button displays a different message detailed in the following example. By default, the unit displays time, date, and an indicating bar of capacity status on a monitor as shown next.

Default display

 

The TOP

Current

The END

 

 

of the HDD

Position

of the HDD

(Capacity Used)

(Capacity Remaining)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

09-05-2003

16:13:02

 

 

 

 

 

 

 

(Date)

(System Time)

 

 

 

 

Press the Display button once; the DVR will display the following sample message plus the default

display. Press the Display button again; the unit will not display any OSD message. Press the button one more time to back to the default display.

Seagate

ST380020A/P

80GB

5400 RPM

 

ST340810A/P

40GB

5400 RPM

 

 

 

 

Maxtor

4A160J0-1A

160GB

5400 RPM

 

4R080L0-1

80GB

5400 RPM

 

 

 

 

 

6Y120L0-1

120GB

7200 RPM

NOTE: Hard-disk drives not shown on this list have not been tested by the engineering team and are not recommended for use with this product. For the latest updated list on the recommended hard-disk drives, please contact your dealers or distributors.

Table 3.3 A.

1+ 2: 59G

 

12.4 HR

QUALITY: BEST

NTSC

RATE: 6 HR

 

20 F/S

MUX : OFF

 

9K

HD

P

SIZE

POS

1

Y

20 G

39.5% P

2

Y

39 G

0.0% R

IP : 192 . 168 . 1 . 90

Description of Table 3.3 A

(1+2: 59G): Total capacity of installed hard-disk, 59 GB

(12.4 HR): Total 12.4 hour recording time available

(

): Timer record activated

(

): Alarm record activated

(QUALITY: BEST): Record quality setting, BEST

(NTSC): NTSC system

(RATE: 6 HR): Setting of Record time mode, 6 hours

(20 F/S): Record speed setting, 20 fields/sec

(MUX: OFF): Only connected to a single camera.

(

): Audio function activated

 

(

): Indicate which HDD is activated

(9K): The image file size

 

(HD): Hard-disk Compartment

 

(P): Y Hard-disk installed; .

No hard-disk installed

(SIZE 20G): The capacity of the installed hard-disk

(POS): Percentage of system;

R: Recording; P: Playback

(IP : 192 . 168 . 1 . 90): Setting of the Ethernet

 

communication,192.168.1.90

(

): External signal

 

( X): Cannot operate at now

 

* About the location of the buttons, please refer to Page 10 2.1 Front View.

18

19

Image 10
Contents Digital Video Recorder Safety Precautions for USA and Canada AvertissementSafety Precautions for Europe and Australia Power SystemTable Of Contents Product Features Product FeaturesProduct Introduction Description of the FRONT/REAR View Front ViewʽTHIS Figure is Looked from the Rear Rear View Alarm In/OutNo Connection Connecting with a Multiplexer InstallationConnecting with a Single Camera Basic ConnectionAttaching AN External Device to DVR Connecting with a QuadClock SET IDE Hard-Disk Drive InstallationSystem Information Quality Best Ntsc Rate 6 HRUpdating System Software Configuring Recording SettingsBasic Operations Ntsc MUX onPAL MUX on Audio OFFPAL MUX OFF Recording Operations Timer RecordingManual Recording Alarm Recording Externally triggered RecordingFast Forward/Reverse Playback OperationsREC Stop Play Play Back Recorded Video from a HDD of the mobile rack Search OperationsSlow Forward/Reverse Full List SearchThumbnail Search Alarm list SearchTime Search Mobile Rack HD Backup Backup OperationsSD Card Search Disk Setting Reformat HD2 Usage Secure Digital Card SD Card BackupAlarm Select Main Backup Alarm to HD2 Save to J0000.JPGKey Lock Operation Menu SetupTransfer the system setting info of DVR to another KEY FunctionsPRE- Alarm OFF Main Alarm REC Enable REC Quality REC SettingAlarm Setting REC Quality Best Disk FullPRE- Alarm NET Enable Clock / TimerNET Enable OFF NET Dhcp NET IP SET FTP Setting Main CommunicationREC Mode Alarm REC Comm Setting FTP Setting Comm IDEnable REC ModeMain Menu Record Disk Setting Disk Setting SystemHD 1 MAC Menu Backgnd SD SetupBios DateCommunication Protocol SetupRS-232 & RS-485 Protocol DEC HEXMobile Rack Installation Page System Default SET RS232 / RS485D Message Meanings S.D MessageNetwork Viewer and Image Viewer Network ViewerURL of a Proxy CancelView the VR-601 video from a remote PC PortView single device Viewing images View all the connected devicesFunction Buttons Description Set the Alarm record settings Change the Record & Timer Properties Via the NetworkSet the regular record settings Set the record timerImage Viewer Archive Images to the ComputerNetwork Configuration Index TableConfigure Your DVR Network Settings RJ-45 PIN configuration for LAN HubEnable Dhcp Function Enable DVR Network Function12.3 TCP/IP Communication Software Connection Testing 12.4 TCP/IP installation12.5 TCP/IP Configuration setting Click Start Æ Settings Æ Control Panel Æ NetworkDesign and specifications subject to change without notice SpecificationsModel Number VR-601 U VR-601 E Colors Compatible MultiplexersManufacturer Model Channel Decode onPrecautions