JVC VR601 instruction manual S.D Message, Network Viewer and Image Viewer, D Message Meanings

Page 31

9. O.S.D Message

No.

O.S.D Message

Meanings

1

NO DISK

No hard-disk detected after power activated

 

 

 

2

BATTERY LOW

Suggest change the battery and reset the system time

 

 

 

3

LOADING

System Boot up

 

 

 

4

VIDEO LOSS

Video loss

 

 

 

5

VIDEO IN

Video input source

 

 

 

6

KEY LOCKED

Key lock function is on

 

 

 

7

KEY UNLOCKED

Key lock function is off

 

 

 

8

n1 OF n2 ITEMS PROGRESS n3 %

BACKUP n1/n2 NOW n3 %

 

 

 

9

BACKUP COMPLETE

Backup complete

 

 

 

10

HD2 SPACE NOT ENOUGH

HD2 has not enough space for backup

 

 

 

11

NO RECORD FOR BACKUP

No backup is possible.

 

 

 

12

BACKUP INCOMPLETE

Backup incomplete, since the user has pressed the STOP

button to stop it

 

 

13

NOT FOUND

The system cannot find a video in the Search function.

 

 

 

14

END

Playback of recorded video has reached the end point

 

 

 

15

DISK FULL

Hard-disks are full; this happens only when the DISK FULL

item in the setup menu is set to STOP.

 

 

16

EMPTY

The user presses the PLAY button or uses the SEARCH

function, but no video can be played.

 

 

17

SET TO NTSC, PLS RESTART

System has to be set to NTSC, please reboot (PAL is similar)

 

 

 

18

SOFTWARE UPDATE

Software update

 

 

 

19

PLEASE RESTART

The system should be rebooted after the software has been

updated

 

 

20

NO DISK

The user has pressed the Save key without putting in a SD

card, or there is a disk error.

 

 

21

DATA NOT CONTINUOUS

The system finds data in installed HDs cannot be used

contiguously. Suggest you remove HD2 from the system.

 

 

22

DISK ATTACHED

HD2 has been attached.

 

 

 

23

DISK REMOVED

HD2 has been removed.

 

 

 

24

FAN STOPPED

The chassis fan has stopped for over 30 seconds.

10. Network Viewer and Image Viewer

This section provides instructions for installing and using the Network Viewer, and Image Viewer, which are included with the VR-601. The programs can be operated by a selected PC equipped with the following requirements.

1.Intel Pentium 233MHz at least.

2.32 MB RAM

3.Window 95, 98, NT, ME, 2000 and XP.

4.4 MB Video card capable of 24-bit true color display.

5.5 MB free hard-disk space for software installation.

6.10-base T network for LAN operation.

10.1The Network Viewer

10.1.1Introduction to Network Viewer

The Network Viewer allows you to potentially access 16 units of the VR-601 from a remote desktop or a laptop in a TCP/IP networking environment. It can perform the following functions.

zView live images from the VR-601

zStore, search, and review recorded video from the VR-601 HDD.

zChange the regular record, event record, and timer properties.

Before you are ready to view images from a desktop, you need to have your VR-601 networked by obtaining a 10 base Ethernet data cable (Standard RJ-45) to connect the VR-601 to your LAN/WAN. Now enter the main menu to set the IP address.

25

HDn ERROR AT xxxxx

There is a hard-disk error during recording, where n is the

hard-disk number and xxxxx is the hexadecimal location.

 

 

26

NOT PRESENT

When the user tries to clear a disk that was not attached in

the setup menu.

 

 

27

SAVE TO DISK

Start saving to the JPEG file.

 

 

 

28

SAVE TO Fnnn. JPG

Save to Fnnn. JPG (where nnn= 0..999)

 

 

 

29

SAVE OK

Save to the JEPG is ok.

 

 

 

30

SD CARD WRITE PROTECT

A SD card is write-protected; or there is an error

 

 

 

31

WAIT . . .

The composition of the hard-disk is changing now. Or, it is

saving the image into the SD card. Please wait for a while.

 

 

 

RJ-45

 

 

 

 

VR-601

 

 

 

 

RJ-45 PIN configuration for Ethernet

 

 

 

PIN NO.

PIN Assignment

1.

TX +

2.

TX -

3.

RX +

4.

Not Connected

5.

Not Connected

6.

RX -

7.

Not Connected

8.

Not Connected

PC

RJ-45 socket

1 2 3 4 5 6 7 8

60

61

Image 31
Contents Digital Video Recorder Avertissement Safety Precautions for USA and CanadaPower System Safety Precautions for Europe and AustraliaTable Of Contents Product Features Product FeaturesProduct Introduction Front View Description of the FRONT/REAR ViewʽTHIS Figure is Looked from the Rear Rear View Alarm In/OutNo Connection Basic Connection InstallationConnecting with a Single Camera Connecting with a MultiplexerAttaching AN External Device to DVR Connecting with a QuadClock SET Quality Best Ntsc Rate 6 HR Hard-Disk Drive InstallationSystem Information IDENtsc MUX on Configuring Recording SettingsBasic Operations Updating System SoftwarePAL MUX on Audio OFFPAL MUX OFF Recording Operations Timer RecordingManual Recording Externally triggered Recording Alarm RecordingFast Forward/Reverse Playback OperationsREC Stop Play Full List Search Search OperationsSlow Forward/Reverse Play Back Recorded Video from a HDD of the mobile rackThumbnail Search Alarm list SearchTime Search Mobile Rack HD Backup Backup OperationsSD Card Search Save to J0000.JPG Secure Digital Card SD Card BackupAlarm Select Main Backup Alarm to HD2 Disk Setting Reformat HD2 UsageKEY Functions Menu SetupTransfer the system setting info of DVR to another Key Lock OperationREC Quality Best Disk Full REC SettingAlarm Setting PRE- Alarm OFF Main Alarm REC Enable REC QualityPRE- Alarm Communication Clock / TimerNET Enable OFF NET Dhcp NET IP SET FTP Setting Main NET EnableREC Mode Comm Setting FTP Setting Comm IDEnable REC Mode Alarm RECMain Menu Record Disk Setting Disk Setting SystemHD 1 Date Menu Backgnd SD SetupBios MACDEC HEX SetupRS-232 & RS-485 Protocol Communication ProtocolMobile Rack Installation Page SET RS232 / RS485 System DefaultNetwork Viewer S.D MessageNetwork Viewer and Image Viewer D Message MeaningsPort CancelView the VR-601 video from a remote PC URL of a ProxyView single device Viewing images View all the connected devicesFunction Buttons Description Set the record timer Change the Record & Timer Properties Via the NetworkSet the regular record settings Set the Alarm record settingsArchive Images to the Computer Image ViewerIndex Table Network ConfigurationEnable DVR Network Function RJ-45 PIN configuration for LAN HubEnable Dhcp Function Configure Your DVR Network Settings12.3 TCP/IP Communication Software Click Start Æ Settings Æ Control Panel Æ Network 12.4 TCP/IP installation12.5 TCP/IP Configuration setting Connection TestingDesign and specifications subject to change without notice SpecificationsModel Number VR-601 U VR-601 E Decode on Compatible MultiplexersManufacturer Model Channel ColorsPrecautions