JVC VR601 instruction manual Alarm list Search, Thumbnail Search, Time Search

Page 17

4.4.2 Alarm list Search

Take the following steps to proceed with the alarm-list search function.

(1)Press the Search button to enter the search mode.

(2)Select the ALARM LIST and press the Enter button to access the complete list of alarm-event recorded video.

(3)Highlight the specific recorded video of your requirement and press the Enter button to display the selected video.

(Key Operation: Press the ^” and “v” buttons, to select a video; press the “<” and “>” buttons, to flip over a page.)

4.4.4 THUMBNAIL Search

Take the following steps to proceed with the thumbnail search function.

(1)Press the Search button to enter the search mode.

(2)Select the THUMBNAIL and press the Enter button to access the thumbnail page.

(3)Set the date you wish to search for the recorded video.

(4)Press the Enter button to start searching and displaying the concerned image.

You can set up by using the “<” button , the “>” button , the “^” button

and the

“v” button

to move eye focus.

 

 

 

You can also set up by using the Shuttle Ring and the Jog Dial to move eye focus.

is the equal of the “<” button ,

is the equal of the “>” button ,

is the equal of

SEARCH

FULL LIST

ALARM LIST TIME SEARCH THUMBNAIL SD CARDʳ

HD 1

A 1 11-18-02 13:22:16 16. 3M

A2 02-14-03 16:55:45 15. 6M A 3 02-17-03 13:22:38 17. 8M

the “^” button

and is the equal of the “v” button .

(5)There are 5 levels of recording range modes to choose from: 1 Hour, 10 Minutes, 1 Minute, 10 Seconds and 1 Second. Select the specific field of your requirement and press the Enter button to enter the next level. If you want to return the previous level, please press the Setup button

(6)Once reaching the critical point at any level, the user can start playback by just clicking the PLAY button .

4.4.3 TIME Search

Take the following steps to proceed with the time search function.

(1)Press the Search button to enter the search mode.

(2)Select the TIME SEARCH and press the Enter button to access the time-setting page.

(3)Set the time period you wish to search for the recorded video.

(4)Press the Enter button to start searching and displaying the concerned image.

(5)If no video is found, please return to the time-setting page and repeat steps (3) and (4) again for another search.

SEARCH

 

 

THUMBNAIL

 

MM

DD

YEAR

 

FULL LIST

 

 

 

 

03

 

/ 13 /

2003

 

ALARM LIST

 

 

 

 

 

 

 

TIME SEARCH

 

 

 

 

 

 

 

THUMBNAIL

 

 

 

 

 

 

 

 

SD CARDʳ

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

SEARCH

FULL LIST

ALARM LIST TIME SEARCH THUMBNAIL SD CARDʳ

 

 

 

TIME SEARCH

 

MM

DD

YEAR

HH

MM

 

 

/ 17 /

2002

00 :

00

11

* About the location of the buttons, please refer to Page 10 2.1 Front View.

* About the location of the buttons, please refer to Page 10 2.1 Front View.

32

33

Image 17
Contents Digital Video Recorder Avertissement Safety Precautions for USA and CanadaPower System Safety Precautions for Europe and AustraliaTable Of Contents Product Introduction Product FeaturesProduct Features Front View Description of the FRONT/REAR ViewNo Connection Rear View Alarm In/OutʽTHIS Figure is Looked from the Rear Connecting with a Single Camera InstallationConnecting with a Multiplexer Basic ConnectionClock SET Connecting with a QuadAttaching AN External Device to DVR System Information Hard-Disk Drive InstallationIDE Quality Best Ntsc Rate 6 HRBasic Operations Configuring Recording SettingsUpdating System Software Ntsc MUX onPAL MUX OFF Audio OFFPAL MUX on Manual Recording Timer RecordingRecording Operations Externally triggered Recording Alarm RecordingREC Stop Play Playback OperationsFast Forward/Reverse Slow Forward/Reverse Search OperationsPlay Back Recorded Video from a HDD of the mobile rack Full List SearchTime Search Alarm list SearchThumbnail Search SD Card Search Backup OperationsMobile Rack HD Backup Alarm Select Main Backup Alarm to HD2 Secure Digital Card SD Card BackupDisk Setting Reformat HD2 Usage Save to J0000.JPGTransfer the system setting info of DVR to another Menu SetupKey Lock Operation KEY FunctionsAlarm Setting REC SettingPRE- Alarm OFF Main Alarm REC Enable REC Quality REC Quality Best Disk FullPRE- Alarm NET Enable OFF NET Dhcp NET IP SET FTP Setting Main Clock / TimerNET Enable CommunicationEnable Comm Setting FTP Setting Comm IDREC Mode Alarm REC REC ModeHD 1 Disk Setting SystemMain Menu Record Disk Setting Bios Menu Backgnd SD SetupMAC DateRS-232 & RS-485 Protocol SetupCommunication Protocol DEC HEXMobile Rack Installation Page SET RS232 / RS485 System DefaultNetwork Viewer and Image Viewer S.D MessageD Message Meanings Network ViewerView the VR-601 video from a remote PC CancelURL of a Proxy PortFunction Buttons Description Viewing images View all the connected devicesView single device Set the regular record settings Change the Record & Timer Properties Via the NetworkSet the Alarm record settings Set the record timerArchive Images to the Computer Image ViewerIndex Table Network ConfigurationEnable Dhcp Function RJ-45 PIN configuration for LAN HubConfigure Your DVR Network Settings Enable DVR Network Function12.3 TCP/IP Communication Software 12.5 TCP/IP Configuration setting 12.4 TCP/IP installationConnection Testing Click Start Æ Settings Æ Control Panel Æ NetworkModel Number VR-601 U VR-601 E SpecificationsDesign and specifications subject to change without notice Manufacturer Model Channel Compatible MultiplexersColors Decode onPrecautions